background image

P3

INTRODUCTION

              QUALITY GUARANTEE AND WARRANTY

QUALITY GUARANTEE

SAM Machinery products are guaranteed against any defects in either material or manufacture for a period of 

24 months from delivery date provided that the equipment has not been subject to abuse or misuse, operated 

incorrectly, over loaded or used for purposes other than for which the equipment is designed or is not maintained 

correctly or if fitted with other than genuine parts.

Claims are only valid when approved by the manufacturer. No person or agent is authorised to assume any 

liability. 

As the use of the equipment is outside our control we can only guarantee quality. No liability for loss, direct 

expenses incurred from the use of this equipment or from any other cause of in respect of performance etc. can be 

accepted.

Defective parts must be returned freight paid to the distributor or available to be inspected as directed. Should such 

parts prove to the manufacturers satisfaction to be faulty - repair of - replacement of defective parts shall 

constitute fulfillment of guarantee obligations. Parts destroyed, lost or tampered with nullify guarantee.

WARRANTY

SAM Machinery products as designed and supplied by Coombridge & Alexander Ltd, are warranted against faulty 

workmanship and defective materials for a period of 24 months from date of purchase. Such warranty is subject to 

the following conditions:

1. 

That the basic maintenance (as noted in p5) is followed.

2. 

This warranty covers the repair or replacement of parts or machinery sold by Coombridge &  

Alexander Ltd and damaged as a result of faulty workmanship or faulty materials. 

It does not extend to any other loss or damage including consequential loss or  damage to other  

property or persons.

3. 

No responsibility will be accepted for repairs made other than by Coombridge & Alexander Ltd without prior 

authorisation by Coombridge & Alexander Ltd.

a. 

Without limiting the generality of paragraph 1. above, this warranty does not cover the following;

b. 

Losses sustained through delay in delivery

c. 

Travel expenses

d. 

Damage caused by accident, misuse or abuse

4. 

Damage to any goods which have been altered or modified by someone other than Coombridge &  

Alexander Ltd or its authorised dealers.

5. 

Procedure for recovery under warranty;

1. 

No loss or damage will be covered under warranty unless the following procedure is followed by            

 

the purchaser.

 

1.  If the purchaser is an authorised dealer -

 

 

a. 

PFG Australia Ltd must first be advised of details of the goods concerned, the loss or 

 

 

 

damage sustained and the circumstances in which the loss or damage arose.

 

 

b. 

After consultation with Coombridge & Alexander Ltd they will then decide if such loss or  

 

 

 

damage is within the terms of warranty and shall advise the dealer as to how the loss or  

 

 

 

damage is to be repaired.

 

2.  If the purchase is not an authorised dealer - 

 

 

a.  

The loss or damage should be reported directly to PFG Australia Ltd who will consult with  

 

 

 

Coombridge & Alexander Ltd, PFG Australia will advise whether it is covered by the  

 

 

 

              warranty and direct the purchaser accordingly as to what action is to be taken.

Содержание 3.8 TONNE SINGLE AXLE
















Отзывы: