SainSmart Coreception Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 11

background image

www.sainsmart.com

[email protected]

Property of SainSmart.com. Unlawful to copy or reproduce in any manner without the express written consent.

·Example motor cable from amazon. Ensure your motor connectors are the same.

here.

Image via 3dwork.io

10. What are the stock stepper drivers?

·X and Y use MKS 2208 v1.0 in standalone mode.
·E uses a MKS A4988
·Both Z drives use MKS A4988

11. What is the leadscrew pitch?

It is 2.54.

12. What Degree is the z axis steppers?

0.9 degrees

13. What mode micro stepping are stepper driver using?

1/16 stepping

14. Jerking or no movement on 1 or more axis or Z lead screws.

·This is typically a failure of the stepper driver or a disconnected motor cable.

«
...
3
4
5
6
7
...
»

Содержание Coreception












Отзывы:

Нет отзывов

Похожие инструкции для Coreception

Бренд: LabelTac Страницы: 2

Бренд: DataCard Страницы: 7

Бренд: Oki Страницы: 16

Бренд: Olivetti Страницы: 179

Бренд: Olivetti Страницы: 36

Бренд: Oki Страницы: 679

Бренд: Oki Страницы: 40

Бренд: OKIDATA Страницы: 308

Бренд: OKIDATA Страницы: 9

Бренд: OKIDATA Страницы: 2

Microline 8480 FB

Бренд: Oki Страницы: 12

Бренд: Raise3D Страницы: 32

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 629

Бренд: Xerox Страницы: 20

Бренд: Xerox Страницы: 61

Versant 80 Press

Бренд: Xerox Страницы: 26

Versant 80 Press

Бренд: Xerox Страницы: 230

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды