Sail F 4 Скачать руководство пользователя страница 13

22

 5. Tilt support bar equipped models: Hold the rear of the top cowling or the 

rear rhandle (if equipped) with one hand and tilt the outboard motor up fully 

un-til the tilt support bar automatically locks.

6. Tilt support knob equipped models: Hold the rear of the top cowling with 

one hand, fully tilt the outboard motor up, and push the tilt support knob into 

the clamp bracket.

7. Tilt support lever equipped models: Hold the rear handle and tilt engine up 

fully until the tilt support lever automatically locks.

NOTE:

Tilt support lever/bar equipped models: If the motor is not facing forward, the 

tilt support lever/bar cannot automatically turn to the locked position. If the tilt 

support lever/bar does not automatically lock, swing the motor a little to the 

left and right.

Procedure for tilting down (manual tilt models)

1. Slightly tilt the outboard motor up.

2. If the tilt support bar equipped: Slowly tilt the outboard motor down while 

pulling the tilt support bar lever up.

3. If the tilt support knob equipped: pull out it, then slowly tilt the engine down.

4. Loosen the steering friction adjuster by turning it counterclockwise, and a-

djust the steering friction according to operator preference.

If there is too much resistance it could be difficult to steer, which could 

result in an accident.

  Unit  

model

       F4-L                 F4-S   

item 

 Dimension 
 OveralI lenth

       680                  680     

       400                  400     

       23.8                 23.8    

       1200                1080     

 OveraII Width

 OveraII height

Weight(AL)S

 Performance 

Full throttle 0perating range 

5250~5750 

 Maximum Output 

kW(HP)@r/min    3(4)@5500 

  Idle speed(in neutral)

r/min

 r/min

  1600

±

100

 Engine

 Type 

 4

scroke S 

 Displacement 

cm3

112

mm  

Bore

×

stroke

59x41

Ignition System

TCl

 (NGK) 

Spark plug

 BPR7HS 

mm

Spark plug gap

0.6-0.7

CORlrol syscem 

Tiller

Starting carburetion system

Choke valve

Valve clearance(COld engine)  lN

0.08-0.12

0.08-0.12

Valve clearance(COld engine)  EX

Drive unit
Gear positions

Forward-neutral-reverse

Gear ratio

2.08(27

13)

 Trim and tilt system   

Manual tilt

Propeller mark

BS

Fuel and oil
Recomended fuel

Unleaded regular gasoline

Fuel tank capacity (inner/outer) 

1.3/18

Recommended engine oil

4-stroke outboard motor oil

Engine oil grade   

APl    

SE

SF

SG

SH

SJ

Engine oil type 

SAE

10W30 or 10W40

Lubrication

Wet sump

Engine oil quantity(excluding oil filter)

L

L

0.60

0.65

Gear oil quantity 

cm3

120

Tightening torque for engine

Spark plug

Engine oil drain bolt

25.0 

N

m

N

m

18.0

mm
mm

  mm

  mm

mm

kg

Specifications

23

Содержание F 4



















Отзывы: