SAHP 130, Инструкция по установке и обслуживанию

Страница: 12 / 41

12| SAHP - Installation Manual
V3 June 2021US - SD667052
5.1 Aluminum Panel (evaporator) Connections
/ i>Õ“ˆ˜Õ“«>˜iiÛ>«œÀ>̜À >Ã>ÎÉn»“>iy>ÀiVœ˜˜iV̈œ˜
ˆµÕˆ`ˆ˜iÌ>˜`ÎÉn»“>iy>ÀiVœ˜˜iV̈œ˜}>ÜÕ̏iÌÌ >Ì>œÜÃ
connection of the panel to the SAHP.
œ˜˜iV̈˜}ÎÉn»Vœ««iÀÀivÀˆ}iÀ>̈œ˜«ˆ«iܜÀŽ“ÕÃÌLiy>Ài`
>˜`ÃiVÕÀi`ÕȘ}ÎÉn»y>Ài˜ÕÌð/œ i«iˆ“ˆ˜>Ìii>ŽÃ]ÕÃi
ÀivÀˆ}iÀ>̈œ˜œˆœ˜Ì iÌ Ài>`œvÌ iÎÉn»y>ÀiVœ˜˜iV̈œ˜ÃLivœÀi
̈} Ìi˜ˆ˜}Ì iy>Ài˜ÕÌ] No soldering or brazing of the copper
line connecting the Evaperator panel to the SAHP is
permitted. The heat pump liquid line must be correctly connected
to the panel liquid inlet. Incorrect orientation will resort in compressor
failure 7KH/LTXLGLQOHWFDQEHLGHQWLƓHGE\WKHWKUHH
LQŴDWHGWXEHVH[WHQGLQJIURPWKHFRQQHFWLRQ3OHDVH
VHHƓJXUH
5.2 Panel Location
The evaperator panel can be located facing any aspect.
On either an exterior wall or pitched roof. If the panel is installed
œ˜>ÀœœvˆÌà œÕ`LiwÝi`ÕȘ}>««Àœ«Àˆ>Ìi܏>ÀÀœœv“œÕ˜Ìˆ˜}
kits in accordance with relevant local and national standards.
5.3 The evaperator panel can be installed in a vertical
(portrait) position or horizontal (landscape) orientation
but there must be a minimum of a 30
O
tilt. the panel
FDQQRWEHODLGŴDWDOVRHQVXUHWKHJDVRXWOHWLVDOZD\V
RULHQWDWHGWRWKHORZHVWSRLQWRIWKHDVSHUWKHƓJXUH
,QFRUUHFWLQVWDOODWLRQZLOOLQKLELWWKHIUHHŴRZRI
lubricating oil
NOTE: Vertical panel orientation offers optimum
SHUIRUPDQFHDOORZLQJHYHQŴRZRIUHIULJHUDQWDFURVVWKH
panel.
NOTE: For increased performance, install the panel
parallel to the prevailing wind allowing the air to pass
freely over the surface of the panel.
REFRIGERATION
INSTALLATION
Liquid
(inlet)
Gas (outlet)
Fig 2
SECTION 5