Sagem MYC-3 Скачать руководство пользователя страница 26

Страница: 26 / 105

Site Technical Documentation - GSM 900/1800 - Serie 3000

Ref. SCT U38 SSC DTS 0020 – Index A -May 4, 200429/03/01

Page 3-

3.3 ERROR MESSAGES DURING START UP

Message

Meaning

Procedure

WARNING

UNTUNED

RADIO

Invalid EEPROM field (SAGEM)

SAGEM Factory Return

PB IMEI

Consistency problem at IMEI level

SAGEM Factory Return

SIM MISSING

SIM card missing or badly inserted

Insert the SIM card

IMEI ERROR

Consistency problem at IMEI level

SAGEM Factory Return

UNTUNED

Mobile not configured

SAGEM Factory Return

(except electronic SWAP

boards sent by SAGEM

Factory which only need a

SMT process)

UNKNOWN BATTERY

Battery not recognised by the mobile

Replace the battery

MOBILE PHONE LOCKED

Number of seizures of sim locked code

exceeded

SAGEM Factory Return
Not repair under warranty

SIM BLOCKED

Three bad PIN codes have been input

Contact the operator

SIM LOCKED (with SIM)

SIM card not adapted to the operator

Replace the SIM card

SIM LOCKED (without SIM) Attempt of corruption ( EEPROM fields)

SAGEM Factory Return
Not repair under warranty

BATTERY TOO LOW

Battery state

Replace the battery

3.4 OTHER ERROR MESSAGES

Message

Meaning

"LINE INCIDENT"

Fax & PC link type "Problems"

"FULL MEMORY"

Fax & PC link type "Problems"

"CLEARING REJECTED"

Fax & PC link type "Problems"

"CHECK CONNECTION"

Fax & PC link type "Problems"

"NOT CONSULTED DOCUMENT"

Fax & PC link type "Problems"

"DEVICE PROBLEM"

Fax & PC link type "Problems"

"VERIFY APPLICATION"

Fax & PC link type "Problems"

"BUSY"

"Problems" related to the network and Communications

"K.PAD LOCKED PRESS *V"

Keypad locked

"OPTION NOT AVAILABLE"

Menu not available for this product version

"PROG.KEY NOT VALID"

Input "Problems"

"ERROR!!"

Calculation error with the calculator (division by zero)

"NOT REACHABLE"

Call forwarding if the mobile is not reachable

"NOT AVAIL."

Not available

"PIN ERROR"

" PIN input problems "

"PIN2 BLOCKED"

Following input errors

Содержание MYC-3










































































































Результаты поиска

Содержание MYC-3

Отзывы:

Бренды по названию

Популярные бренды

Sagem MYC-3, Техническая документация инструкция

Результаты поиска

Содержание MYC-3

Отзывы:

Бренды по названию

Популярные бренды