manualshive.com logo in svg

Saftronics VG520P4, Техническое руководство, Страница: 25 / 62

Поделиться
Скачать
Saftronics VG520P4 Скачать руководство пользователя страница 25

Chapter 2: Handling Inverters

Firmware – S1043

Revision:  2  (9/98)

14

© Saftronics, Inc.

2.3

Checking and Controlling the Installation Site

  CAUTION

•

 

Always hold the case when carrying the Inverter.  If the Inverter is held by the front cover, the main body of the Inverter may fall,
possibly resulting in injury.

•

 

Attach the Inverter to a metal or other noncombustible material.  Fire can result if the Inverter is attached to a combustible material.

•

 

Install a cooling fan or other cooling device when installing more than one Inverter in the same enclosure so that the temperature of
the air entering the Inverters is below 45°C.  Overheating can result in fire or other accidents.

Install the VG5 in the installation site described below and maintain optimum conditions.

2.3.1

Installation Site

Install the Inverter under the following conditions.

Type

Ambient Operating Temperature

Humidity

Enclosed wall-mounted

-10 to 40°C

90% RH or less (no condensation)

Open chassis

-10 to 45°C

90% RH or less (no condensation)

Protection covers are attached to the top and bottom of the Inverter.  Be sure to remove the protection covers before
installing a 200 or 400 V class Inverter with an output of 5 kW or less in a panel.

•

 

Install the Inverter in a clean location free from oil mist and dust.  It can be installed in a totally enclosed panel that is
completely shielded from floating dust.

•

 

When installing or operating the Inverter, always take special care so that metal powder, oil, water, or other foreign
matter does not get into the Inverter.

•

 

Do no install the Inverter on combustible material, such as wood.

•

 

Install the Inverter in a location free from radioactive materials and combustible materials.

•

 

Install the Inverter in a location free from harmful gasses and liquids.

•

 

Install the Inverter in a location without excessive oscillation.

•

 

Install the Inverter in a location free from chlorides.

•

 

Install the Inverter in a location not in direct sunlight.

2.3.2

Controlling the Ambient Temperature

To enhance the reliability of operation, the Inverter should be installed in an environment free from extreme temperature
increases.  If the Inverter is installed in an enclosed environment, such as a box, use a cooling fan or air conditioner to
maintain the internal air temperature below 45°C.

2.3.3

Protecting the Inverter from Foreign Matter

Place a cover over the Inverter during installation to shield it from metal power produced by drilling.

Always remove the cover from the Inverter after completing installation.  Otherwise, ventilation will be reduced, causing
the Inverter to overheat.

Содержание VG520P4































































Отзывы:

Нет отзывов