2
TO SET LOCK:
Press lock/unlock button
(Figure 8)
so the green
locking indicator position is visible. Close door/drawer to engage
lock. Pull on door/drawer to ensure it is locked. Door/drawer is
now set in the locked position.
TO OPEN:
Place the magnetic key over the area where the lock
is installed
(Figure 9)
.
You should hear an audible “click” when
the lock disengages. Open door. Close door/drawer to re-engage
lock.
TO DEACTIVATE FOR PERIODS OF NON-USE:
Press button to
the red, unlocked position.
To Use
Wipe clean. Keep lock dry.
To Clean
To Install
4a
Cabinets—
Open door and line up template top or side edge with
pencil mark from step 2. Press down firmly to stick adhesive
(Figure 4a).
4b
Drawers—
Open drawer and line up template side edge with pencil
mark from step 2. Press down firmly to stick adhesive
(Figure 4b).
5
Fold template inward at dotted line and use a pencil to poke
through and mark two drill locations for catch
(Figures 4a and 4b).
6
Peel paper (labeled
1B
) off template, then close door/drawer
(Figure
5).
Template will transfer from cabinet base to door/drawer
(Figure
6).
If adhesive does not stick, remove bumpers from door or
drawer front.
TIP:
You may be able to open adjacent door and ensure template
transfers.
Drawers—
If you have an inside panel
(see page 1 Image B)
on
your drawer front, the bottom of the template must be flat along
the outer panel as shown in
Figure 7,
or the dotted slots on the
template must be fully on the inner panel as shown in
Figure 7
.
If template does not fit either of these two recommended options, this
lock should not be used on your drawers.
7
NOTE:
If lock is being mounted on a cabinet door with an inset
panel only the part of the template with the diagonal lines should
be overhanging the recess area of the inset panel. If any more of
the template hangs over the recess of the inset panel installation in
this location is not recommended.
Use a pencil to poke through and mark two drill locations for lock
(Figure 6).
Remove template.
8
Visually inspect marked hole locations of the lock to make sure holes
are both the same distance from edge of door/drawers.
To remove the lock, remove screws.
To Remove
8
9
Green = Locked
Red = Unlocked
CAUTION:
DO NOT DRILL THROUGH CABINET DOOR! DO NOT DRILL
THROUGH THIN INSET PANELS. Follow the drill manufacturer’s instructions
when using your drill. Power tools are not recommended for screw
installation.
9
Using a 7/64” drill bit predrill 3/8” deep holes at marked locations.
10
Position catch with flat side facing out as shown
(Figure 7 inset)
and use Phillips head screwdriver to install two screws. Position lock
as shown and use Phillips head screwdriver to install two screws
(Figure 7).
11
Test the lock.
Set lock to the locked position by pushing the lock/unlock
button so the green locking indicator is visible. Close door/drawer. Place
magnetic key over area where lock is installed and open cabinet door/
drawer to ensure it can open and close easily with no interference.
7b
7a
Determine Lock Placement
(continued)
1B
PEEL
OFF
2
SCREW HOLE
S
FOR CA
TC
H
FOLD
3
SC
RE
W
H
OL
ES
FOR L
OCK
4a
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
3
SCREW HOLES
FOR LOCK
FOLD
2
SCREW HOLES
FOR CATCH
1B
PEEL OFF
FOLD
1A
PEEL OFF
1B
PEEL
OFF
2
SCREW HOLE
S
FOR CA
TC
H
FOLD
5
6
2
SCREW HOLE
S
FOR CATC
H
1B PEEL
OFF
FOLD
2
SCREW
HOLES
FOR CATCH
1B PEEL
OFF
FOLD
4b
7
OK
OK
OK
3
SCREW HOLE
S
FOR LOCK
3
SCREW HOLE
S
FOR LOCK
