Safe Fleet PRIME DESIGN VCR3-FT21B Скачать руководство пользователя страница 3

PRIME DESIGN, A SAFE FLEET BRAND 

 Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 

 Phone: 651-552-8554 

 Toll Free: 1.8.PRIME.RACK 

 Fax: 651-552-1799 

 Email: [email protected] 

 Website: www.primedesign.net

TM & © 2019 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING

3

VCR3-FT21B 

ASSEMBL

Y INSTR

UCTIONS–P

A

CKA

GING CONTENTS

8—Front Drive Shaft .............................................. (Qty 1)

  B Version, 35.75”

7—Connecting Bar ................................................. (Qty 1)

 48.00”

11—Quick Clamp Tube Splice Assembly .............. (Qty 1) 

5.00“

13—Clamp Down Handle Latch Assembly ........... (Qty 1)

10—Clamp Down Tube .......................................... (Qty 1)

 80.00”

12—Removable Horn with Cap ............................. (Qty 1) 

15.00”

14—Clamp Down Handle Assembly ..................... (Qty 1) 

9— Heavy Duty Front Hook Assembly .................. (Qty 1) 

M8 x 45MM (1X)

M8 Lock Nut (1X)

Clamp Down Handle (1X)

" Flat Washer (2X)

" Flat Washer (10X)

Anti-Seize (1X)

Lubricant (1X)

Clevis Pin (1X)

Cotter Pin (1X)

M8 x 50MM (4X)

 ⅜" x 2.25" (2X)

1.00" Sealing 

Stickers (16X)

M8 Lock Nut (5X)

⅜" Lock Nut (2X)

⅜" Flat Washer (4X)

M8 x 25MM (1X)

17—HKT-8163 (Not called out in Overview) ........ (Qty 1)

16—USQSG-Ergorack ............................................ (Qty 1)

       Quick Start Guide, Clamp Down, Rotation

¼ Flat Washer (2X)

¼ Lock Washer (2X)

M6 x 20MM (2X)

L Post Bracket Clamp (2X)

Z Post (2X)

L Post (2X)

15—L & Z Post Kit.................................................. (Qty 1) 

  Adj. Z Post, 7.25”, L Post, w/HKT-0160

Содержание PRIME DESIGN VCR3-FT21B













Отзывы: