background image

SafeTrack – Hardware Installation Guide

2

Table of Contents

1 INTRODUCTION .......................................................................................3

2  SAFETRACK HARDWARE ........................................................................3

2.1  SafeTrack Hub 

3

2.2  SafeTrack LED  

3

2.3  SafeTrack Relay 

4

2.4  SafeTrack Tag 

4

3  INSTALLING THE SAFETRACK HUB .......................................................5

3.1  Mount Recommendations 

5

3.2  Mechanical Mount 

6

Access Available Behind Mount Wall 

6

Access NOT Available Behind Mount Wall 

6

3.3  Electrical Install 

6

3.3.1 Power Supply 

6

Hub Harness Power Supply Connector ......................................................6

3.3.2 Battery Signal Input 

7

4  INSTALLING THE SAFETRACK LED ........................................................8

4.1  Mechanical Mount 

8

4.2 Electrical 

9

5  INSTALLING THE HUB EXTERNAL ANTENNA .....................................10

5.1  Mount Recommendations 

11

5.2  Mechanical Mounting 

11

6  INSTALLING THE SAFETRACK RELAY ..................................................12

6.1  Mount Recommendations 

12

6.2  Mechanical Mounting 

12

6.2.1 Mechanical Install Procedure 

13

Access Available Behind Mount Wall 

13

Access NOTE Available Behind Mount Wall 

13

6.3  Electrical Install 

13

7  INSTALLING THE  SAFELINK TAG ..........................................................14

Prior to Mounting 

14

7.1  Drill Tap  Hole 

15

Precautions 15

7.2  Secure Tie 

15

Precautions 15

7.3 Adhesive 

16

Precautions 16

8  PARTS LIST .............................................................................................17

Содержание FRC SafeTrack





















Отзывы: