Saf-Fro DIGISTEEL III 320C, Инструкции по технике безопасности при эксплуатации и обслуживании, Страница: 11 / 263

EN
DIGISTEEL III 320C / DIGIPULS III 320C 11
List of accessible parameters in
COnFIG
menu
Left
display
Right display Step Default Description
GrE On
-
;OFF
–
Aut Aut
Configuration of the Water Cooling Unit. 3 possibles states :
-
On
: Forced on, watercooler is always activated
-
OFF
: Forced off, watercooler is always desactivated
-
Aut
: Automatic mode, Watercooler works when according need
ScU nc
–
no
-
OFF OFF
Security of water cooling. 3 possible states :
-
nc
: Normally closed,
-
no
: Normally open,
-
OFF
: Desactivate
Unit US
–
CE CE
Unit displayed for wire speed and thickness:
- US : inch unit
- CE : meter unit
CPt OFF
–
0
,
01
–
1
,
00 0
,
01
s
0
,
30
Trigger holding time in order to call program (Only in 4T welding mode).
Can be use only for welding program from 50 to 99.
PGM no
–
yES no
Activate / desactivate program management mode
PGA OFF
–
;000
–
020
%
1
%
OFF
Use to setup available adjustement range of the following parameters: wire speed, arc
voltage, arc dynamics, pulse fine-setting. Use only when program management is
activated and programs are locked.
Adj Loc – rC Loc
Select adjustement Wire speed and arc voltage :
- Loc : Local on the power source
- rC : remote Control or torch potentiometer
CAL OFF
–
on OFF
Calibration of torch & ground harness
L 0
–
50 1
uH
14
Cable choke setting / display
r 0
–
50
1

8
Cable resistor setting / display
SoF no
–
yES no
Software update mode.
FAC no
–
yES no
Factory settings reset. Pressing
YeS
will cause a reset of the parameters to factory
defaults when exit SETUP menu.
List of accessible parameters in
CYCLE
menu
Left
display
Right display Step Default Description
tPt 00.5
–
10.0 0
,
1
s
0
,
5
Spot time. In Spot mode and in Manual mode, the Hot Start, Downslope and sequencer
settings cannot be changed
PrG 00.0
–
10.0 0
,
1
s
0
,
5
Pre-gas time
tHS OFF
–
00.1
–
10.0 0
,
1
s
0
,
1
Hot start time
IHS
--
70
–
70 1
%
30
Hot start current (wire speed). X%

the welding current
UHS
--
70
–
70 1
%
0
Hot start voltage X%

the arc voltage
dYn
--
10
+
10
--
20
+
20
1
%
0
Fine setting in short arc
rFP
--
10
+
10
--
20
+
20
1
%
0
Fine setting in pulse
dyA 00
–
100 1 50
Arc striking dynamics at electrode
tSE OFF
–
0.01
–
2.50 0
,
01
s
OFF
Sequencer time (Sequencer, only in synergic mode)
ISE
--
-90
+
90 1
%
30
Sequencer current level. X%

the welding current
dSt OFF
–
00.1
–
05.0 0
,
1
s
OFF
Down-slope time
DdSI
--
70
–
00.0 1
% --
30
Down-slope current (wire speed). X%

the welding current
dSU
--
70
–
70 1
%
0
Down-slope voltage. X%

the arc voltage
Pr_ 0.00
–
0.20 0
,
01
s
0
,
05
Anti-stick time
PrS Nno
–
yES no
Pr-Spray activation
PoG 00.0
–
10.0 0
,
05
s
0
,
05
Post-gas time
3.3.4. Program management
DIGISTEEL III 320C / DIGIPULS III 320C allows creating, store and modifying up to 99 welding programs directly on front panel from
program
00
to program
99
. This function is activated by moving parameter
PGM
from
no
to
YES
in
COnFIG
menu.
P00
is the working program in any state. (Program management mode activated or desactivated). When power source is working on
this program, the Led indicator “JOB” is switched off. All commutators are accessible in this mode, so it will be used to set programs.
P01
to
P99
are program saved, only if program management mode is activated. When power source is working on these programs,
the led indicator “JOB” is switched on. In this mode, commutators welding process, wire diameter, gas and metal are not available.
When a program selected has been modified, the indicator “JOB” blinks.