SAB Heli Division Goblin 770 Competition Скачать руководство пользователя страница 42

Страница: 42 / 48

Center Hub

[H0135-S]

Damper

[H0144-S]

- 1 x Secondary Shaft M3.

- 1 x Socket Head Cap Screw

Shoulder M2.5x19mm.

- 1 x Metric Hex Nylon Nut

M2,5H3,5.

- 1 x Socket Head Cap Shoulder

M3x22mm.

- 1 x Metric Hex locknut Nuts M3H4.

Secondary Shaft

[H0157-S]

- 1 x Center Hub.

- 1 x Socket Head Cap Screw

Shouldered M4x24mm.

- 1 x Metric Hex Nylon Nut M4 H5..

- 2 x Socket Head Cap Screws

M3x12mm.

-2 x Damper Derlin.

-2 x Washers 10x 16x1mm.

-4 x Washers 10x 16x0.2mm.

-4 x Orings 3050.

- 1 x Bearing 3 Support.

- 1 x Motor Support.

- 1 x Flanged Bearing 6x 13x5mm.

- 2 x Socket Head Cap Screws

M3x8mm.

- 2 x Set Screws M5x20mm.

- 2 x Washers 5.3x 15x1mm.

- 2 x Metric Hex Nylon Nuts M5H4.8.

- 2 x Finishing Washers M3.

- 2 x Socket Head Cap Screws

M3x10mm.

- 2 x Metric Hex Nylon Nut M3 H4.

- 2 x Springs de 5.8/ df0.5 / LL9.

- 2 x Springs de 3/ df0.5 / LL12.

Bearing Support

[H0142-S]

Motor Mount

[H0143-S]

- 1 x Bearing 3 Support.

- 1 x Flanged Bearing

6x 13x5mm.

- 2 x Socket Head Cap Screws

M3x8mm.

Battery Tray

[H0149-S]

- 1 x Battery Plate.

- 1 x Battery Protection.

- 2 x Cylinder M2.5.

- 2 x Flat Head Cap Screw

M2.5x5mm

- 1 x Heat Shrink.

- 1 x Stop Battery Tray.

- 2 x Socket Head Cap

Screw M2.5x8mm.

Stop Battery Tray

[H0150-S]

Carbon Fiber ESC Support

(H0153-S)

- 1 x Carbon Fiber ESC Support.

- 6 x Flat Head Socket Cap

M2,5x5mm.

- 1 x 19T Drive Pinion.

- 1 x Socket Head Cap Screw

Shouldered M3x22mm.

- 1 x Metric Hex Nylon Nut

M3H4.

19T Drive Pinion

[H0156-S]

Aluminum Blade Spacer

[H0158-S]

- 4 x Aluminum Blade Spacer

Canopy Positioner

[H0159-S]

- 2 x Canopy Positioner.

- 2 x Socket Head Cap Screws

M3x10mm.

- 1 x CF Red Landing Gear.

Red Landing Gear

[H0162-S]

- 1 x Aluminum Double Bearing

One Way Pulley.

- 3 x Shims 10x 16x0,2mm.

- 1 x One Way Brass Bushing.

Double Bearing One Way Pulley

[H0171-S]

- 1 x Aluminum Front Tail Pulley.

- 1 x Socket Head Cap M2.5x19mm.

- 1 x Metric Hex Nylon Nuts M2,5H3,5.

Aluminum Front Tail Pulley

[H0172-S]

- 1 x Column Belt Tensioner.

- 1 x Tail Belt Idler.

- 1 x Belt Tensioner Arm.

- 2 x Flanged Bearings 3x 7x3mm.

- 2 x Flanged Bearings 5x 9x3mm.

- 1 x Socket Head Cap Screw M3x50mm.

- 1 x Washer 3x 4x0.5mm.

- 1 x Socket Head Cap Screw M3x12mm.

- 2 x Washers 3.2x 6x0.5mm.

- 1 x Button Head Cap Screw M3x4mm.

- 1 x Spring De8/df0.5/LL8.

Belt Tensioner Support

[H0174-S]

- 1 x 18T Pulley.

- 1 x Set Screws M4x4mm.

- 1 x 19T Pulley.

- 1 x Set Screws M4x4mm.

19T Pulley

[H0175-19-S]

18T Pulley

[H0175-18-S]

- 1 x 22T Pulley.

- 1 x Set Screws M4x4mm.

22T Pulley

[H0175-22-S]

- 1 x 21T Pulley.

- 1 x Set Screws M4x4mm.

21T Pulley

[H0175-21-S]

- 1 x 20T Pulley.

- 1 x Set Screws M4x4mm.

20T Pulley

[H0175-20-S]

- 1 x 24T Pulley.

- 1 x Set Screws M4x4mm.

24T Pulley

[H0175-24-S]

- 1 x 23T Pulley.

- 1 x Set Screws M4x4mm.

23T Pulley

[H0175-23-S]

- 2 x Blade Grip.

- 2 x

Thrust Bearing

10x 18x5.5mm.

- 4 x

Bearing 10x 19x5mm.

- 2 x Washer 10x 16x1mm.

- 2 x Button Head Socket Cap M4x10mm.

Blade Grip

[H0182-S]

Blade Grip Arm

[H0183-S]

- 2 x Blade Grip Arm.

- 2 x Socket Head Cap Screw

M4x10mm.

- 2 x Uniball M3x4 Ø5 H3.5.

Swashplate Anti-Rotation Guide

[H0152-S]

- 1 x CF Swashplate

Anti-Rotation Guide.

- 1 x Finishing Washer M3.

- 1 x Socket Head Cap Screw

M3x8mm.

Page 40

Chapter 18, Spare Parts

Содержание Goblin 770 Competition













































Результаты поиска

Содержание Goblin 770 Competition

Отзывы:

Похожие инструкции для Goblin 770 Competition

Бренды по названию

Популярные бренды

SAB Heli Division Goblin 770 Competition, Руководство пользователя

Результаты поиска

Содержание Goblin 770 Competition

Отзывы:

Похожие инструкции для Goblin 770 Competition

Бренды по названию

Популярные бренды