background image

21

Fig. 25

OPERATION

  Rotate the control arm until the pointer aligns with the 

desired angle on the miter scale.

  Release the miter lock plate. 

  

NOTE: 

You can quickly locate 0

°

, 22-1/2

°

 left or right, and 

45

°

 left or right by releasing the lock plate as you rotate 

the control arm. The lock plate will seat itself in one of the 
positive stop notches, located in the miter table frame.

  Tighten the miter lock handle securely.

  Place the workpiece flat on the miter table with one edge 

securely against the fence. If the board is warped, place 
the convex side against the fence. If the concave edge of 
a board is placed against the fence, the board could col-
lapse on the blade at the end of the cut, jamming the blade.

  When cutting long pieces of lumber or molding, support 

the opposite end of the stock with a roller stand or with 
a work surface level with the saw table. 

See Figure 29.

  Align cutting line on workpiece with edge of saw blade.

  Grasp  the  stock  firmly  with  one  hand  and  secure  

it against the fence. Use the optional work clamp or a 
C-clamp to secure the workpiece when possible.

  Before turning on the saw, perform a dry run of the cutting 

operation just to make sure that no problems will occur 
when the cut is made.

  Grasp  the  saw  handle  firmly  then  squeeze  the  switch 

trigger.  Allow  several  seconds  for  the  blade  to  reach 
maximum speed.

  Slowly lower the blade into and through the workpiece. 

  Release the switch trigger and allow the blade to stop 

rotating before raising the blade out of workpiece. Wait 
until the electric brake stops blade from turning before 
removing the workpiece from the miter table.

TO BEVEL CUT

See Figures 25 - 26.

A bevel cut is made by cutting across the grain of the workpiece 
with the blade angled to the workpiece. A straight bevel cut 
is made with the miter table set at the zero degree position 
and the blade set at an angle between 0° and 45°.

  Pull out the lock pin and lift saw arm to its full height.

  Loosen the miter lock handle. Rotate the miter lock handle 

approximately one-half turn to the left to loosen.

  Press the miter lock plate down with thumb and hold.

  Rotate the control arm until the pointer aligns with zero 

on the miter scale.

  Release the miter lock plate. 

  

NOTE: 

Quickly locate zero by releasing the lock plate as 

you rotate the control arm. The lock plate will seat itself 
in one of the built-in positive stop notches, located in the 
miter table frame.

  Tighten the miter lock handle securely.

  The  45°  triangle  on  the  miter  fence  provides  for  the  

maximum clearance required for adjusting the miter saw’s 
angle when making a bevel or compound cut.

  Loosen the bevel lock knob and move the saw arm to 

the left to the desired bevel angle.

  Bevel angles can be set from 0

°

 to 45

°

  Align the indicator point for the desired angle.

  Once  the  saw  arm  has  been  set  at  the  desired  angle, 

securely tighten the bevel lock knob. 

  Place the workpiece flat on the miter table with one edge 

securely against the fence. If the board is warped, place 
the convex side against the fence. If the concave edge 
of a board is placed against the fence, the board could 
collapse on the blade at the end of the cut, jamming the 
blade. 

See Figures 31 - 32.

  When cutting long pieces of lumber or molding, support 

the opposite end of the stock with a roller stand or with 
a work surface level with the saw table. 

See Figure 29.

  Align the cutting line on the workpiece with the edge of 

saw blade.

Fig. 26

WORK 

CLAMP

BEVEL 

SCALE

INDICATOR 

POINT

INDICATOR 

SCREW

SCALE 

INDICATOR

BEVEL CUT

Содержание TS1342































Отзывы: