background image

17

ASSEMBLY

Fig. 13

WARNING:

Make  sure  the  spindle  lock  button  is  not  engaged   
before  reconnecting  saw  into  power  source.  Never   
engage spindle lock button when blade is rotating.

NOTE:

 

Many of the illustrations in this manual show only  

portions of the compound miter saw. This is intentional so that 
we can clearly show points being made in the illustrations. 

Never  operate  the  saw  without  all  guards  securely  in 

place and in good operating condition.

SQUARING  THE  MITER  TABLE  TO  THE 

FENCE

See Figures 13 - 16.

  Unplug the saw.

  Push down on the saw arm and pull out the lock pin to 

release the saw arm. 

  Raise saw arm to its full raised position.

  Loosen  the  miter  lock  handle  approximately  one-half 

turn.

 

Depress the miter lock plate and rotate the miter table 
until the pointer on the control arm is positioned at 0

°

.

  Release the miter lock plate and securely tighten the miter 

lock handle.

  Lay a framing square flat on the miter table. Place one 

leg of the square against the fence. Place the other leg 
of the square beside the throat plate in the miter table. 
The edge of the square and the throat plate in the miter 
table should be parallel as shown in figure 13.

  If the edge of the framing square and the throat plate in 

the miter table are not parallel as shown in figures 14 and 
15, adjustments are needed.

  Using the blade wrench provided, loosen the socket head 

screws securing the fence. Adjust the fence left or right 
until the framing square and throat plate are parallel.

  Retighten the screws securely and recheck the fence-to-

table alignment.

Fig. 14

Fig. 15

VIEW OF MITER TABLE SQUARE WITH FENCE 

VIEW OF MITER TABLE NOT SQUARE WITH FENCE, 

ADJUSTMENTS ARE REQUIRED

VIEW OF MITER TABLE NOT SQUARE WITH FENCE, 

ADJUSTMENTS ARE REQUIRED

MITER 

LOCK PLATE

MITER 

LOCK HANDLE

MITER 

FENCE

MITER TABLE

THROAT PLATE

FRAMING 

SQUARE

MITER 

LOCK PLATE

MITER 

FENCE

MITER TABLE

THROAT PLATE

FRAMING 

SQUARE

MITER 

LOCK PLATE

MITER 

FENCE

MITER TABLE

THROAT PLATE

FRAMING 

SQUARE

Содержание TS1342































Отзывы: