Ryobi RY48RM76A, Книга

Страница: 7 / 308

Ŷ Replace damaged blades and bolts in sets to preserve
balance.
Ŷ Be careful during adjustment of the product to prevent
entrapment of the fingers between moving blades and
fixed parts of the product.
Ŷ The cutting blades continue to rotate for a few seconds
after the motor is turned off. When servicing the blades,
be aware that even though the power source is switched
off, the blades can still be moved. Never place any part
of the body in the blade area until you are sure the
blades have stopped rotating.
Ŷ The blade on the product is sharp. Use extreme caution
and wear heavy-duty gloves when fitting, replacing,
cleaning or checking bolt security.
Ŷ
After each use, clean the product with a soft, dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
Ŷ Keep the product free of grass, leaves, or other debris
build-up.
Ŷ
Do not use water to clean the product. Use an air moving
device, such as a compressor or leaf blower to remove
grass, leaves, or other debris build up.
TYRE MAINTENANCE
The product is equipped with tubeless tyres with the
following dimensions:
Ŷ
Front: 33 x 13 x 15 cm
Ŷ Rear: 40 x 16 x 20 cm
When tyres are worn, the traction of the mower decreases,
which increases the chance of having an accident. Replace the
tyres when the depth on the tread is 4 mm or less, or any time
there is damage to the tyre. Always use original replacement
tyres. Using improper tyres on the product could cause loss of
control, which could cause serious personal injury.
Have the tyres replaced only by an authorised service
centre.
TYRE AIR PRESSURE
Check the air pressure in all four tyres before each use. Improper
air pressure a
ႇ ects handling, steering response, traction, tyre
life, level cutting, and operator comfort. Make sure that tyres are
in
À
ated to the recommended air pressure of 1.4 bar.
Tyre air pressure should only be measured or adjusted
when tyres are cold.
TYRE REPAIR
If a leak or
À
at tyre occurs due to a puncture, the tyre may
be repaired using a plug-type patch. If the damage is from
a cut, or if the puncture cannot be repaired using a plug,
replace the tyre.
BRAKE ADJUSTMENT
See page 258.
If the mower travels further before stopping when stepping
on the brake pedal, the brakes need adjusting.
After
¿
nal adjustment, test the brakes by driving the mower
at normal speed on
À
at ground to be sure that the mower
stops quickly when brake pedal is stepped on.
CLEARING BLOCKAGES
Ŷ
Turn off the product, engage the parking brake,
and remove the start key. Set the cutting deck to the
maximum height. Make sure that all moving parts have
come to a complete stop.
Ŷ Always wear heavy-duty gloves when checking or
clearing a blockage. The blades are sharp and the
blockage itself could be a sharp object.
Ŷ Check and carefully clear the side discharge chute for
blockages.
Ŷ Carefully remove any found blockages. Remember that
the blade may move during cleaning.
KNOW YOUR PRODUCT
See page 246.
1. Blade engage knob
The blade engage knob activates or stops the cutting
blades.
Ɣ Pull up the blade engage knob to activate the blades.
Ɣ Press the blade engage knob to stop the blades.
NOTE: The blades should stop within 5 seconds. If the
blades do not stop, contact an authorised service centre.
2. Headlight button
The headlight button turns the headlights ON and OFF.
3. Power switch
The power switch turns the product ON and OFF. The
start key must be inserted before the switch can be
operated. When the key is in the accessory position,
the power switch is also used to power optional
manufacturer-approved mower accessories.
4. Reverse mode button
The reverse mode button turns on the blades when
manoeuvring in the reverse direction.
NOTE: The blades do not turn on during reverse
operation if the reverse mode button is not pressed and
the blade engage knob is not pulled up.
5. Battery level indicator / hour meter
The battery level indicator shows the amount of battery
charge remaining. The hour meter tracks the total
number of hours the product has been used (key in on
position) for maintenance purposes.
6. Seat (with operator presence safety interlock
system)
The seat has an interlock system that stops the blades
if the operator leaves the mower while the blades are
running.
Test the system before each use to ensure that it is
working correctly.
1. Press the blade engage knob to stop the blades.
2. Insert the start key, and turn it to the ON position.
3. Pull up the blade engage knob to activate the blades.
4. Briefly stand up but do not get off the mower.
The blades should stop within 5 seconds. If the blades
do not stop, contact an authorised service centre.
Do not operate the mower until the safety interlock
system has been repaired.
7. Charging port
The charging port connects the charger to the mower.
The LED indicator provides the status of the battery
during charging.
8. Hitch plate
The hitch plate can be used to tow loads of 136 kg (300
lbs.) or less.
9. Cup holder
The cup holder provides a convenient place to store
cups or water bottles.
10. Deck height adjustment lever
The deck height adjustment lever raises or lowers the
cutting deck.
ENGLISH
EN
ES
IT
NL
PT
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
7
Original Instructions