Ryobi RG-3500, Руководство по эксплуатации для владельца

Страница: 9 / 12

8
CAUTION!
Do not store fuel from one season to another.
CAUTION!
Never place any type of storage cover on the generator
while it is still hot.
When transporting or storing your generator for extended
periods of time:
• Empty the fuel tank.
• Disconnect the spark plug.
• Do not obstruct any ventilation openings.
• Keep the generator in a cool dry area.
The cross-sectional of cable should not be less than that of
below annex, and the length should not longer than 10m .
CHANGING/ ADDING OIL
NOTE:
You should check the oil level of your generator according to
the maintenance schedule. When the oil level is low you will
need to add oil until the level is sufficient to run the
generator.
The oil capacity of your generator engine is 0.6L oz.
AIR CLEANER MAINTENANCE
Routine maintenance of the air cleaner helps maintain
proper airflow to the carburetor. Occasionally check that the
air cleaner is free of excessive dirt.
1. Unhinge the clasps at the top and bottom of the air
cleaner cover (Fig.14, Fig. 15).
2. Remove the sponge-like elements from the casing.
3. Wipe the dirt from inside the empty air cleaner casing.
4. Wash the sponge-like elements in household detergent
and warm water. Allow to drying.
5. Soak the dry elements in engine oil. Squeeze out any
excess oil.
6. Replace the sponge-like elements in the air cleaner
casing and replace the cover.
FUEL FILTER CUP CLEANING
The fuel filter cup is a small well underneath the fuel valve.
It helps to trap dirt and water that may be in your fuel tank
before it can enter the engine. To clean the fuel filter cup:
1. Turn the fuel valve to the "OFF' position (Fig. 12).
2. Unscrew the fuel filter cup from the fuel valve using a
wrench. Turn the valve toward you to unscrew (Fig. 16).
3. Clean the cup of all sediment. Using a rag or brush.
4. Reinstall the fuel filter cup.
The spark plug is important for proper engine operation. A
good spark plug should be intact, free of deposits, and
SPARK PLUG MAINTENANCE
EMPTYING THE FUEL TANK
STORAGE
properly gapped. To inspect you spark plug:
1. Pull on the spark plug cap to remove it.
2. Unscrew the spark plug from the generator using the
spark plug wrench included with this product (Fig. 17).
3. Visually inspect the spark plug. If it is cracked or chipped,
discard and replace with a new spark plug.
4. Measure the plug gap with a gauge (Fig. 18). The gap
should be 0.7-0.8mm (0.028
-
0.031 in).
5. If you are re-using the spark plug, use a wire brush to
clean any dirt from around the spark plug base and then
re-gap the spark plug.
6. Screw the spark plug back into its place on the generator
using the spark plug wrench.
7. Replace the spark plug cap.
Before storing your generator for extended periods of time,
you should drain your generator of petrol. To drain the
generator of fuel:
1. Turn the fuel valve to the "OFF" position.
2. Remove the fuel filter cup.
3. Empty the fuel filter cup of any fuel.
4. With a receptacle underneath the generator to catch the
fuel, turn the fuel valve to the "ON" position. Drain all the
fuel from the generator.
5. Turn the fuel valve to the "OFF" position.
6. Replace the fuel filter cup.
7. Store the emptied petrol in a suitable place.
It is only necessary to drain the oil from the crankcase if it
has become contaminated with water or dirt. In this case,
you can drain the oil from the generator according to the
following steps:
1. Place a bucket underneath the generator to catch oil as it
drains.
2. Using a hex wrench, unscrew the oil drain plug, which is
located on the crankcase underneath the oil filler/dipstick
cap (Fig. 13). Allow all the oil to drain from the generator.
3. Replace the oil drain plug and tighten with a hex wrench.
To add oil to the crankcase, follow these steps:
1. Make sure the generator is on a level surface.
2. Unscrew the oil filler/dipstick cap from the engine (Fig. 1).
3. Using a funnel, add high detergent motor oil to the
crankcase. We recommend SAE 10W30 motor oil for
general use. When full, the oil level should come close in
the top of the oil fill opening (Fig. 2).
Never dispose of used motor oil in the trash or down
a drain. Please call your local recycling center or
auto garage to arrange oil disposal.
4. Insert the dipstick as if you were replacing the cap and
then remove again. There should now be oil on the stick.
If there is no oil on the stick, or oil only at the very end of
the stick, you should add oil until the engine crankcase is
filled.
5. Be sure to replace cap when finished checking oil.
RATED CURRENT & CROSS SECTIONAL OF CORD
Rated Current of
electrical equipment (A)
>0.2 & ≤3
>3 & ≤6
>6 & ≤10
>10 & ≤16
>16 & ≤25
>25 & ≤32
>32 & ≤40
>40 & ≤63
≤0.2
0.5
a
0.75
1.0 (0.75)
b
1.5 (1.0) b
2.5
4
6
10
Cross Sectional of
cord (mm )
ANNEX