background image

4

English (Original Instructions)

Do not operate the saw using only one 

hand.
Engines produce carbon monoxide which 

is an odorless, deadly poison. Do not 

operate in an enclosed area.
Wear non-slip, heavy-duty protective 

gloves when handling the chainsaw.

Always wear safety boots with non-slip 

sole.
Use unleaded petrol intended for motor 

vehicle use with an octane rating of 91 [(R 

+ M)/2] or higher. This product is powered 

by 2-stroke cycle engine and requires pre-

mixing petrol and 2-stroke lubricant.

Bar and chain lubricant

Use 2-stroke oil for air cooled engines.

Regulatory Compliance Mark (RCM). 

This product meets applicable regulatory 

requirements.
Guaranteed sound pressure and sound 

power lever

Set ignition switch to RUN (I) position.

Make sure chain brake is disengaged.

Fully press and release primer bulb 10 

times.

Pull choke lever all the way out. This also 

sets the throttle to fast idle.

Pull starter until engine attempts to start 

(no more than 5 pulls).

Push choke lever all the way in.

Pull starter until engine runs (6x Max).

Chain brake ON.

Squeeze and release throttle.
Mix the fuel mix thoroughly and also each 

time before refueling.

Add bar and chain oil (to the bar and chain 

reservoir) every time that fuel is added to 

the chainsaw’s fuel tank.
Mix fuel outdoors where there are no 

sparkles or flames.
Do not smoke when mixing fuel or filling 

fuel tank.

 

Fuel and oil
Rotate to adjust chain tension
"+" = Tighten the chain
"-" = Loosen the chain
Moving direction of the chain
H = High speed adjustment needle
L = Low speed adjustment needle
T = Idle adjustment screw

Lock the filter access cover.

Unlock the filter access cover.

Ignition switch:
I = ON, O = Stop

Set the brake lever to Brake (Stop) position

SERVICE

Servicing requires extreme care and knowledge 

and  should  be  performed  only  by  a  qualified  service 

technician. For service we suggest you return the product 

to your nearest authorised service center for repair. When 

servicing, use only identical replacement parts.

 WARNING

To avoid serious personal injury, do not attempt 

to use this product until you read thoroughly and 

understand completely the operator’s manual. If you 

do not understand the warnings and instructions in the 

operator’s manual, do not use this product. Call Ryobi 

customer service for assistance.

Содержание RCS5145N





















Отзывы: