background image

13

SYMBOLS

Safety Alert Symbol

Indicates danger, warning or caution. It means attention!!! 
Your safety is involved.

Read Your Operator's
Manual

Your manual contains special messages to bring attention
to potential safety concerns as well as operating and 
servicing information. Please read all the information 
carefully to ensure satisfaction and safe use.

Wear Eye and Hearing
Protection

Eye and hearing protection must be worn when operating 
this equipment.

Risk of Electric Shock

Hazardous Voltage. Disconnect from power source before
servicing. Do not use in damp conditions.

Hot Surface

To reduce the risk of injury or damage, avoid contact with
any hot surface.

Unexpected Starting

The compressor may start without warning.

Recycle Symbol

Waste electrical products should not be disposed of with 
household waste. Please recycle where facilities exist. 
Check with your Local Authority or retailer for recycling 
advice.

CE Marking

Conforms to relevant safety standards.  

Air and condensation water can burst from the 
compressor when the drain plug is removed.

Risk of Bursting

Enclosure Alert

Do not operate the portable compressor with the doors 
or enclosure open.

Содержание RC-2050NV

















Отзывы: