Ryobi RBCGM25BB Скачать руководство пользователя страница 13

Страница: 13 / 14

English (Original Instructions)

TROUBlESHOOTInG

PROBlEM

POSSIBlE CaUSE

SOlUTIOn

Engine will not start

1. Switch set to the O (OFF) position.

1. Set switch to the I (ON) position.

2. No spark

2. Remove the spark plug. Re-attach the spark plug

cap and lay the spark plug on the metal cylinder.

Pull the starter cord and watch for a spark at the

spark plug tip. If there is no spark, repeat the test

with a new spark plug.

3. No fuel

3. Push primer bulb until the bulb is full of fuel. If the

bulb does not fill, the primary fuel delivery system

is blocked. If the primer bulb fills, the engine may

be flooded. (See next item.)

4. Flooded engine

4. Remove the spark plug. Turn the product so that

the spark plug hole is aimed at the ground. Make

sure the choke lever is set to position B and pull

the starter cord 10 to 14 times. This clears excess

fuel from the engine. Clean and reinstall the spark

plug. With the throttle trigger fully depressed, pull

the starter cord 3 times. If the engine does not

start, set the choke lever to A and follow normal

starting instructions. If the engine still fails to start,

repeat the procedure with a new spark plug.

5. Starter cord is hard to pull

5. Contact an authorized service dealer.

Engine does not reach full speed

and emits excessive smoke

1. Incorrect oil/fuel mixture

1. Use fresh fuel and the correct 2-stroke oil mix.

2. Air filter is dirty

2. Clean the air filter according to the instructions in

the Maintenance section.

3. Spark arrestor screen is dirty

3. Contact an authorized service dealer.

Cutting line will not advance when

using bump feed action

1. Line welded to itself

1. Lubricate with silicone spray.

2. Not enough line on the spool

2. Install more line.

3. Line worn too short

3. Pull line while alternately pressing down on and

releasing the bump knob.

4. Line tangled on spool

4. Remove line from spool and rewind.

5. Engine speed too slow

5. Advance line at full throttle.

6. Line spool installed back to front

6. Ensure the writing on the line spool is facing the

correct way; THIS SIDE OUT FOR STRAIGHT

SHAFT.

Grass wraps around the trimmer

head assembly and the attachment

shaft

1. Cutting tall grass at ground level

1. Cut tall grass from the top down.

2. Operating the product at part throttle 2. Operate the product at full throttle.

Oil drips from muffler

1. Operating the product at part throttle 1. Operate the product at full throttle.

2. Incorrect oil/fuel mixture

2. Use fresh fuel and the correct 2-stroke oil mix.

3. Air filter is dirty

3. Clean the air filter according to the instructions in

the Maintenance section.

Содержание RBCGM25BB















Результаты поиска

Содержание RBCGM25BB

Отзывы:

Бренды по названию

Популярные бренды

Ryobi RBCGM25BB, Руководство оператора

Результаты поиска

Содержание RBCGM25BB

Отзывы:

Бренды по названию

Популярные бренды