Ryobi RBC42FSB Скачать руководство пользователя страница 11

16

English(Original instructions)

 

1 Litre 

33 ml   = 

 

2 Litres   + 

67 ml   =

 

3 Litres   +   100 ml   = 

30:1

 

4 Litres   +   133 ml   = 

 

5 Litres   +   167 ml   =

Filling the tank

 

Clean surface around fuel cap to prevent 
contamination.

 

Loosen the fuel cap slowly to release pressure and to 
keep fuel from escaping around the cap.

 

Carefully pour fuel mixture into the tank. Avoid spillage.

 

Prior to replacing the fuel cap, clean and inspect the 
gasket.

 

Immediately replace fuel cap and hand tighten. Wipe 
up any fuel spillage. Move 9 m away from refuelling 
site before starting engine.

NOTE: 

It is normal for smoke to be emitted from a new 

engine during and after first use.

 

 WARNING

Always shut off engine before fuelling. Never add fuel to 
a machine with a running or hot engine. Move at least 9 
m (30 ft) from refuelling site before starting the engine. 
Do not smoke.

OPERATING THE STRING TRIMMER

See 

fi

 gure 9.

 

Hold the product with the right hand on the trigger 
handle and the left hand on the left handle. Keep a 
firm grip with both hands while in operation. 

 

The product should be held at a comfortable position 
with the trigger handle about hip height.

 

Always operate the product at full throttle. Prolonged 
cutting at partial throttle will result in lubricant dripping 
from the silencer.

 

Cut tall grass from the top down to prevent grass from 
wrapping around the shaft housing and string head 
which may cause damage from overheating. 

 

If grass becomes wrapped around the string head, 
stop the engine, disconnect the spark plug wire, and 
remove the grass. 

CUTTING TIPS

See 

fi

 gure 10.

 

Keep the product tilted towards the area being cut. 

 

Do not use in dangerous environments.

 

Use the tip of the string to do the cutting; do not force 
the string head into the uncut grass.

 

Wire and picket fences cause extra string wear, even 
breakage. Stone and brick walls, kerbs and wood may 
wear string rapidly.

 

Avoid trees and shrubs. Tree bark, wood mouldings, 
cladding and fence posts can be easily damaged by 
the string.

STARTING AND STOPPING

See 

fi

 gure 13 - 14.

Choke position A

Choke position B

 

 WARNING

Never start or run the engine inside a closed or poorly 
ventilated area; breathing exhaust fumes can kill.

To start a cold engine:

1.  Lay the product on a 

fl

 at, bare surface.

2.  Set the ignition switch to the “I” (ON) position.
3.  Push the primer bulb approximately 5 times.
4.  Set the choke lever to position A (choke closed).
5.  Pull the starter grip with a quick 

fi

 rm  and  consistent 

upward motion until the engine starts.

6.  Set the choke lever to position B (choke open).
7.  Allow engine to warm up for 30 seconds prior to 

operation.

To start a warm engine:

1.  Lay the product on a 

fl

 at, bare surface.

2.  Set the ignition switch to the “I” (ON) position.
3.  Set the choke lever to position B (choke open).
4.  Pull the starter grip with a quick 

fi

 rm  and  consistent 

upward motion until the engine starts.

To stop the engine:

Set the ignition switch to the “O” (OFF) position.

OPERATING THE BRUSHCUTTER

See 

fi

 gure 11 - 12.

 

Hold the product with the right hand on the trigger 
handle and the left hand on the left handle. Keep a 
firm grip with both hands while in operation.

 

The product should be held at a comfortable position 
with the trigger handle about hip height.

 

Maintain your grip and balance on both feet. Position 
yourself so that you will not be drawn off balance by 

Содержание RBC42FSB















Отзывы: