6
WARNING
The tool is capable of driving a fastener without making
contact with a workpiece. Always point the tool away
from yourself or others and always direct the fastener
toward the work surface before pulling the trigger.
Failure to do so could result in possible serious
personal injury.
Connect the tool to the air supply with a 1/4 in. female
quick connector. For maximum tool performance, a 3/8 in.
VXSSO\OLQHDQG¿WWLQJVDUHUHTXLUHG
NO-MAR PAD
6HH¿JXUH
The no-mar pad attached to the nose of the product helps
prevent marring and denting when working with softer
woods.
WARNING
Disconnect the product from the air supply before
removing or replacing the no-mar pad. Failure to do so
could result in serious personal injury.
The pad can be removed by pulling it down and away from
WKHQRVH7RUHSODFHWKHSDG¿WLWLQWRSODFHRYHUWKHQRVH
LOADING THE TOOL WITH FASTENERS
6HH¿JXUH
WARNING
Keep the tool pointed away from yourself and others
when loading fasteners. Failure to do so could result in
possible serious personal injury.
WARNING
2QO\ WKRVH IDVWHQHUV VSHFL¿HG XQGHU 6SHFL¿FDWLRQV
PD\EHXVHG:KHQ¿OOLQJWKHPDJD]LQHKROGWKHWRRO
so that the nose is not pointing towards the operator or
any other person or animals.
WARNING
The tool’s driving mechanism may cycle when the tool
LV¿UVWFRQQHFWHGWRWKHDLUVXSSO\$OZD\VFRQQHFWWKH
tool to a pressurized air supply before loading fasteners
to prevent injury from unintended cycling. Always make
sure the tool’s magazine is empty at the beginning of
each work session, before connecting to an air supply.
1. Connect the tool to the air supply.
2. Release the magazine latch and slide open the
magazine.
3. With the nose of the tool pointed away from you, feed
a strip of fasteners into the magazine. Be sure the
fasteners are pointed downward.
4. Close the magazine.
WARNING
Use only the fasteners recommended for use with this
tool. The use of any other fasteners can result in tool
malfunction, leading to serious injuries.
WARNING
Never load fasteners with the trigger activated. Doing
so could result in possible serious personal injury.
WARNING
Do not use fasteners with width smaller than that stated
LQ6SHFL¿FDWLRQV'RLQJVRPD\FDXVHIDVWHQHUVWRH[LW
the tool prematurely through the guide track. Do not use
hardened fasteners with pneumatic tools. This could
lead to excessive wear of the guide body and allow
fasteners to exit the back of the guide body, leading to
serious personal injury.
DRIVING A FASTENER
6HH¿JXUH
WARNING
Do not pull the dual actuation trigger system unless the
nose is pressed against the work surface. Accidental
actuation will occur and could cause serious personal
injury.
Avoid triggering the fastener driving tool if the magazine
is empty.
Any defective or improperly functioning fastener driving tool
must immediately be disconnected from the compressed
air supply and passed to a specialist for inspection.
In the event of longer breaks in work or at the end of the
working shift, disconnect the tool from the compressed air
supply and it is recommended to empty the magazine.
The compressed air connectors of the fastener driving tool
and the hoses should be protected against contamination,
the ingress of coarse dust chips, sand, etc, will result in
leaks and damage to the fastener driving tool and the
couplings.
Single sequential actuation mode
The tool employs single sequential actuation mode.
1. Connect the tool to the air supply.
2. Load the tool with fasteners.
3.
*ULSWKHWRRO¿UPO\WRPDLQWDLQFRQWURO3UHVVWKH
nose
Содержание RA-NP2325-S
Страница 14: ...11 PARTS LIST...
