![background image](http://html1.mh-extra.com/html/ryobi/ra-np2325-s/ra-np2325-s_operators-manual_1506763008.webp)
5
WARNING
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
VXI¿FLHQWWRLQÀLFWVHYHUHLQMXU\
WARNING
Always wear safety goggles or safety glasses with side
shields when operating tools. Failure to do so could
result in objects being thrown into your eyes resulting
in possible serious injury.
WARNING
Disconnect the tool from the air supply before leaving
the work area, moving the tool to another location, or
handing the tool to another person. Failure to do so
could result in serious personal injury.
WARNING
Always wear eye protection. Eye protection does
QRW ¿W DOO RSHUDWRUV LQ WKH VDPH ZD\ 0DNH VXUH WKH
eye protection chosen has side shields or provides
SURWHFWLRQ IURP À\LQJ GHEULV ERWK IURP WKH IURQW DQG
sides.
PREPARING THE TOOL FOR USE
WARNING
Please read and observe these operating instructions
before using the tool. Basic safety measures should
always be strictly followed to protect against damage to
the equipment and personal injury to the user or other
people working in the vicinity of operation.
Under normal use conditions, the tool should be lubricated
with air tool oil before connecting the tool to an air supply.
$GG DLU WRRO OXEULFDQW LQWR WKH DLU ¿WWLQJ RQ WKH WRRO RQFH
daily with minimal use, or twice a day with heavy use. Only
a few drops of oil at a time is necessary. Too much oil will
only collect inside the tool and will be noticeable in the
exhaust cycle.
Before connecting the tool, check the air compressor
gauge to be sure it is functioning within the proper range
of 4.8 - 8.3 bar (70 - 120 psi).
CONNECTING THE TOOL TO AN AIR SUPPLY
6HH¿JXUH
WARNING
Ensure that the pressure supplied by the compressed
air system does not exceed the maximum allowable
pressure of the fastener driving tool. Set the air
pressure initially to the lower value of the recommended
DOORZDEOHSUHVVXUHVHH6SHFL¿FDWLRQV
WARNING
Empty the magazine to prevent a fastener from being
ejected at the next stage of work in the event that
internal parts of the fastener driving tool are not in the
starting position following maintenance and repair work
or transportation.
WARNING
Connect the fastener driving tool to the compressed
air supply using suitable pressure hose equipped with
quick-action connectors.
WARNING
Check for proper functioning by applying the nose of
the fastener driving tool to a piece of wood or wooden
material and actuating the trigger once or twice.
This tool is designed to operate on clean, dry compressed
air at regulated pressures between 4.8 - 8.3 bar (70 - 120
psi). The correct air pressure is the lowest pressure that
will do the job.
NOTE:
Air pressure that is higher than 8.3 bar (120 psi)
may damage the tool.
The tool and air hose must have a hose coupling that
allows all pressure to be removed from the tool when the
coupling is disconnected.
WARNING
Always use a coupling that discharges all the
FRPSUHVVHG DLU LQ WKH WRRO DW WKH WLPH WKH ¿WWLQJ RU
hose coupling is disconnected. Using a coupling that
does not discharge the compressed air could cause
unintended operation and serious personal injury.
WARNING
Do not climb rigging or scaffolding while carrying a tool
that is connected to an air hose. Doing so could result
in serious personal injury.
Содержание RA-NP2325-S
Страница 14: ...11 PARTS LIST...