background image

9

against a workpiece several times. The tool must 

not operate.

 

● With the safety yoke not engaged on the workpiece, 

point the tool down and away from you and other 

persons, and pull the trigger several times. Hold 

the trigger in this position for a minimum of 5 

seconds. The tool must not operate.

 

● Press the safety yoke firmly against the workpiece, 

and pull the trigger. The tool must operate.

 

● With the safety yoke still depressed, release the 

trigger. The driver must return to its up position.

6.  If the tool successfully meets all the requirements 

in this checklist, it is ready for use. Load the proper 

fasteners for the desired application.

7.  Set the depth of drive according to the “drive depth 

adjustment” section in this manual. Repeat this 

checklist before using the tool each day, or if the tool is 

dropped or damaged in any way.

 WARNINg

Do not use any attachments or accessories not 

recommended by the manufacturer of this tool. The use 

of attachments or accessories not recommended can 

result in serious personal injury.

lUBRIcAtION

An 

automatic 

in-line 

filter-regulator-lubricator 

is 

recommended (Fig. 12) as it increases product life and keeps 

the product in sustained operation. The in-line lubricator 

should be regularly checked and filled with air tool oil.
Proper adjustment of the in-line lubricator is performed by 

placing a sheet of paper next to the exhaust ports and 

actuate the tool 10 - 15 times without fasteners loaded. 

The lubricator is properly set when a light stain of oil 

collects on the paper. Excessive amounts of oil should be 

avoided.
If it becomes necessary to store the product for an extended 

period of time (overnight, weekend, etc.), it should receive 

a generous amount of lubrication at that time. Actuate the 

tool 10 - 15 times without fasteners loaded to ensure oil 

has been evenly distributed throughout the product. The 

product should be stored in a clean and dry environment. 

 

● It is most important that the product be properly 

lubricated by keeping the air line lubricator filled 

and correctly adjusted. Without proper lubrication 

the product will not work properly and parts will 

wear prematurely.

 

● Use correct lubricant in the air line lubricator. The 

lubricator should be of low air flow or changing air 

flow type, and should be kept filled to the correct 

level. Use only recommended lubricants, specially 

made for pneumatic applications. Substitutes 

may harm the rubber compounds in the product's 

O-rings and other rubber parts.

IMpORtANt!

See figure 12.

If  a  filter/regulator/lubricator  is  not  installed  on  the  air 

system, air operated tools should be lubricated at least 

once a day or after 2 hours of work with 2 - 6 drops 

of oil, depending on the work environment, directly 

through the male fitting in the tool housing.

20140514v1

Содержание RA-NBS1832-S

















Отзывы: