background image

9

lUBRIcAtION

An 

automatic 

in-line 

filter-regulator-lubricator 

is 

recommended (Fig. 10) as it increases product life and keeps 

the product in sustained operation. The in-line lubricator 

should be regularly checked and filled with air tool oil.
Proper adjustment of the in-line lubricator is performed by 

placing a sheet of paper next to the exhaust ports and 

actuate the tool 10 - 15 times without fasteners loaded. 

The lubricator is properly set when a light stain of oil 

collects on the paper. Excessive amounts of oil should be 

avoided.
If it becomes necessary to store the product for an extended 

period of time (overnight, weekend, etc.), it should receive 

a generous amount of lubrication at that time. Actuate the 

tool 10 - 15 times without fasteners loaded to ensure oil 

has been evenly distributed throughout the product. The 

product should be stored in a clean and dry environment. 

 

● It is most important that the product be properly 

lubricated by keeping the air line lubricator filled 

and correctly adjusted. Without proper lubrication 

the product will not work properly and parts will 

wear prematurely.

 

● Use correct lubricant in the air line lubricator. The 

lubricator should be of low air flow or changing air 

flow type, and should be kept filled to the correct 

level. Use only recommended lubricants, specially 

made for pneumatic applications. Substitutes 

may harm the rubber compounds in the product's 

O-rings and other rubber parts.

IMpORtANt!

See figure 10.

If  a  filter/regulator/lubricator  is  not  installed  on  the  air 

system, air operated tools should be lubricated at least 

once a day or after 2 hours of work with 2 - 6 drops 

of oil, depending on the work environment, directly 

through the male fitting in the tool housing.

20140522v1

Содержание RA-NBA1564-K
















Отзывы: