Ryobi R18GN18, Быстрый старт

Страница: 12 / 16

PRODUCT SPECIFICATIONS
Nailer
Model R18GN18
Voltage 18 V
Magazine capacity (number of nails) 105
Fastener type: Brad
Length 15 mm - 50 mm
(5/8” - 2”)
Diameter 1.2 mm (18 Ga)
Weight - excluding battery pack 2.36 kg
Measured sound values determined according to EN 60745:
A-weighted sound pressure level L
pA
= 85.5 dB(A)
Uncertainty K 3 dB(A)
A-weighted sound power level L
WA
= 96.5 dB(A)
Uncertainty K 3 dB(A)
Wear ear protectors.
The vibration total values (triaxial vector sum) determined
according to EN 60745:
Vibration emission value a
h
= 2.7 m/s
2
Uncertainty K 1.5 m/s 2
BATTERY
Compatible battery pack (not included)
RB18L13
RB18L15
RB18L15A
RB18L15B
RB18L20
RB18L20A
RB18L25
RB18L25A
RB18L40
RB18L40A
RB18L50
RB18L50A
RB18L60A
RB18L90A
RB1815C
RB1820C
RB1825C
RB1840C
RB1840X
RB1850C
RB1850X
RB1860X
WARNING! The declared vibration total values and
the declared noise emission values given in this instruction
manual have been measured in accordance with a
standardised test and may be used to compare one tool with
another. They may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission values represent
the main applications of the tool. However, if the tool is used
for different applications, used with different accessories,
or poorly maintained, the vibration and noise emission
may differ. These conditions may significantly increase the
exposure levels over the total working period.
An estimation of the level of exposure to vibration and noise
should take into account the times when the tool is turned off
or when it is running idle. These conditions may significantly
reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration and noise, such as maintaining
the tool and the accessories, keeping the hands warm (in
case of vibration), and organising work patterns.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Work-contacting element does not depress
fully - product does not operate.
Nails are low.
Work-contacting element is jammed.
Replenish the nails.
Remove the battery and clear the debris.
Product operates properly, but fasteners
are not driven fully.
Air pressure is too low.
Depth of drive is not deep enough.
Nail is too long for wood hardness.
Increase the air pressure.
Adjust the depth of drive.
Use nails of the length that is appropriate for
the wood.
Product operates properly, but fasteners
are driven too deep.
Air pressure is too high.
Depth of drive is too deep.
Decrease the air pressure.
Adjust the depth of drive.
Product jams frequently. Nails are incorrect.
Nails are damaged.
Magazine is loose.
Magazine is dirty.
Verify that the size of nails is correct.
Replace the nails.
Tighten the screws.
Clean the magazine.
Product stops and LED work lights flash
rapidly.
Battery is low or has no charge.
Product is hot.
Recharge the battery.
Allow product to cool.
Product has charged battery and LED work
lights flash slowly.
Product has malfunctioned. Take product to the nearest authorised repair
centre.
Product operates properly, but fasteners
are not driven fully.
Product is too cold (less than 5°C). Warm the product up to the operating
temperature, either by storing in the correct
environment or by firing test shots into spare
material.
Product does not operate. Nail magazine is empty/very low. Refill the magazine.
Product does not operate. Nailing process has been interrupted (by
releasing the trigger mid-way through the
process).
Remove the battery and replace to reset the
system.
Hold the trigger at least 0.5 seconds to fire
a nail.
Product does not operate. Trigger or work piece contact has been
held for too long without activating the nail
firing process.
Release the trigger then activate again.