4
SPECIFIC SAFETY RULES
ADDITIONAL SAFETY RULES
■
■
■
■
■
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool.
Following this rule will reduce the risk of electric
shock, fire, or serious injury.
■
■
■
■
■
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses.
Following this rule will reduce the risk of
serious personal injury.
■
■
■
■
■
Protect your lungs. Wear a face or dust mask if the
operation is dusty.
Following this rule will reduce the
risk of serious personal injury.
■
■
■
■
■
Protect your hearing. Wear hearing protection during
extended periods of operation.
Following this rule will
reduce the risk of serious personal injury.
■
■
■
■
■
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location.
Following this
rule will reduce the risk of electric shock or fire.
■
■
■
■
■
Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condi-
tions that may affect its operation. A guard or other
part that is damaged should be properly repaired or
replaced by an authorized service center.
Following
this rule will reduce the risk of shock, fire, or serious
injury.
■
■
■
■
■
Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges.
Following
this rule will reduce the risk of electric shock or fire.
■
■
■
■
■
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 14 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 50 feet is not recom-
mended. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating.
■
■
■
■
■
Inspect for and remove all nails from lumber before
routing.
Following this rule will reduce the risk of
serious personal injury.
■
■
■
■
■
Drugs, alcohol, medication. Do not operate tool
while under the influence of drugs, alcohol, or any
medication.
Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
■
■
■
■
■
Save these instructions.
Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
WARNING:
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains chemi-
cals known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:
•
lead from lead-based paints,
•
crystalline silica from bricks and cement and
other masonry products, and
•
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out micro-
scopic particles.
SERVICE
■
■
■
■
■
Tool service must be performed only by qualified
repair personnel.
Service or maintenance performed by
unqualified personnel could result in a risk of injury.
■
When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual.
Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
GENERAL SAFETY RULES
■
■
■
■
■
Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact
hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the cutting tool “live” and
shock the operator.
