![background image](http://html1.mh-extra.com/html/ryobi/r181d/r181d_operators-manual_1507411004.webp)
4
SPECIFIC SAFETY RULES
ADDITIONAL SAFETY RULES
■
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
■
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses.
Following this rule will reduce the risk of
serious personal injury.
■
Protect your lungs. Wear a face or dust mask if the
operation is dusty.
Following this rule will reduce the
risk of serious personal injury.
■
Protect your hearing. Wear hearing protection during
extended periods of operation.
Following this rule will
reduce the risk of serious personal injury.
■
Inspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location.
Following this
rule will reduce the risk of electric shock or fire.
■
Check damaged parts. Before further use of the tool,
a guard or other part that is damaged should be care-
fully checked to determine that it will operate prop-
erly and perform its intended function. Check for align-
ment of moving parts, binding of moving parts, break-
age of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is
damaged should be properly repaired or replaced by
an authorized service center.
Following this rule will
reduce the risk of shock, fire, or serious injury.
■
Do not abuse cord. Never carry the tool by the cord
or yank it to disconnect it from the receptacle. Keep
cord away from heat, oil, and sharp edges.
Following
this rule will reduce the risk of electric shock or fire.
■
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gage size (A.W.G.) of at least 14 is rec-
ommended for an extension cord 50 feet or less in
length. A cord exceeding 50 feet is not recommended.
If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating.
■
Inspect for and remove all nails from lumber before
using this tool.
Following this rule will reduce the risk of
serious personal injury.
■
Drugs, alcohol, medication. Do not operate tool while
under the influence of drugs, alcohol, or any medi-
cation.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
■
Save these instructions.
Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
•
lead from lead-based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially
designed to filter out microscopic particles.
SERVICE
■
■
■
■
■
Tool service must be performed only by qualified
repair personnel.
Service or maintenance performed
by unqualified personnel could result in a risk of injury.
■
When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance
section of this manual.
Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
GENERAL SAFETY RULES
■
■
■
■
■
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the cutting tool “live” and
shock the operator.
Содержание R181D
Страница 23: ...23 NOTES...