Ryobi OLT1830H, Оригинальное руководство пользователя, Страница: 6 / 25

4
WARNING
Servicing requires extreme care and knowledge
DQG VKRXOG EH SHUIRUPHG RQO\ EH D TXDOL¿HG VHUYLFH
technician. For service we suggest you return the
product to your nearest authorized service center for
repair. When servicing, use only identical replacement
parts.
Ŷ
Ensure the battery is disconnected and the supply cord
is disconnected from the supply before performing any
maintenance, cleaning or adjustments.
Ŷ
You may make adjustments and repairs described
here. For other repairs, contact the authorized service
agent.
Ŷ
For replacement line use only nylon filament line of
the diameter described in the specification table of this
manual
Ŷ
After extending new cutter line, always return the
product to its normal operating position before starting.
Ŷ
After each use, clean the product with a soft dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorized service centre.
Ŷ
Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition.
INTENDED USE
The product is only intended for use outdoors.
The product is designed for cutting grass, light weeds
and other similar vegetation at or about ground level.
The cutting plane should be approximately parallel to the
ground surface when trimming and approximately vertical
when edging.
The product should not be used to cut or trim hedges,
bushes or other vegetation where the cutting plane is not at
or about ground surface level.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Ŷ
Injury caused by vibration. Hold the tool by designated
handles and restrict working time and exposure.
Ŷ
Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
QXPEQHVV DQG EODQFKLQJ RI WKH ¿QJHUV XVXDOO\ DSSDUHQW
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices are
all thought to contribute to the development of the these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Ŷ
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
Ŷ
After each period of operation, exercise to increase
blood circulation.
Ŷ
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
See page 8.
Parts
1. Rear handle
2. Lock-out trigger
3. Trigger
4. Cord retainer
5. Front handle
6. Handle adjusting knob
7. Upper shaft
8. Telescopic collar
9. Rotating collar
10. Lower shaft
11. Safety guard
12. Cut-off blade
13. Cutting line
14. Extension cord
15. Battery pack
16. Battery latch button
17. Charger
18. Spool cover
19. Spool cover lock button
20. Spool
21. Eyelet
22. Line release button
23. Slot
SYMBOLS ON THE PRODUCT
Safety alert
Read and understand all instructions
before operating the product, follow all
warnings and safety instructions.
Wear ear protection.
Wear eye protection.