1. ON/Measure Button
2. Menu Button (Distance/Area/Volume)/Unit/
Off button
1. Laser on
2. Reference point (front)
3. Reference point (rear)
4. Distance/Continuous measurement
5&6. Measuring mode indication
7. Battery status
8. Previous value
9. Summary line/latest value/calculation result
Remove the battery compartment lid and then
insert 2, 1.5V AAA batteries according to the
direction icons on the inside of the battery
compartment. Replace the lid.
BATTERY REPLACEMENT
If the instrument does not switch on or the
battery symbol has no bars, replace the batteries
as previously stated above.
BATTERY DISPOSAL
You, as the end user, are legally
bound to return all used batteries,
disposal in the household garbage is
prohibited! You can hand over your
used batteries / accumulators at
collection points in your community or wherever
batteries / accumulators are sold.
Follow the valid legal stipulations in
respect of the disposal of the device at the end of
its lifecycle.
BATTERY SAFETY REMINDERS
Please dispose of batteries responsibly; always
observe local, state, and federal regulations with
regard to battery disposal.
Never dispose of batteries in a fire. Batteries may
explode or leak.
Never mix battery types. Always install new
batteries of the same type.
TURNING THE UNIT ON AND OFF
Press the On/Meas button to turn on the unit.
Press the Units button for 3 seconds to turn the
unit off. The unit will automatically power off after
three minutes of inactivity.
MEASUREMENT UNIT
The default unit is meter. Press the Units button
for 2 seconds to change between m/ft+in.
BUTTON FUNCTIONS
2
LCD DISPLAY
8
9
OPERATION
ADJUSTING THE MEASURING REFERENCE
Press the On/Meas and Units button together to
switch the reference point between the top and
the bottom of the instrument. The measuring
point default setting is from the rear of the unit.
SINGLE DISTANCE MEASUREMENT
Press the On/Meas button to activate the laser.
Press the On/Meas button again to trigger the
distance measurement. The measured value is
displayed immediately.
CONTINUOUS MEASUREMENT
Long press the On/Meas button to activate
continuous measurement.
The measured values are displayed on the
screen in real time when moving the device. The
last measured value is displayed in the summary
line. Press the On/Meas button to stop the
function. This function will be stopped automati-
cally after 5 minutes of inactivity.
AREA MEASUREMENT
Press the Units button to select Area measuring
mode . The length line on the icon will flash.
Press the On/Meas button to get the distance for
the length line. Next the width line on the icon will
flash. Press the On/Meas button again to get the
distance for the width line. The area will now be
calculated and displayed in the summary line
and perimeter value in the first line. .
VOLUME MEASUREMENT
Press the Units button to select Volume
measuring mode . The length line on the icon
will flash. Press the On/Meas button to get the
distance for the length line. Next the width line on
the icon will flash. Press the On/Meas button
again to get the distance for the width line. Next
the height line on the icon will flash. Press the
On/Meas button again to get the distance for the
height line. The area will now be calculated and
displayed in the summary line.
GENERAL MAINTENANCE
This instrument is designed to provide years of
dependable service, if the following care
instructions are performed:
Keep the laser measurer dry and free from dust.
Use and store the laser measurer in nominal
temperature conditions. Temperature extremes
can shorten the life of the electronic parts and
distort or melt plastic parts.
Handle the laser measurer carefully and avoid
shock and vibration. Dropping the meter may
damage the electronic parts or the case.
Keep the laser measurer clean. Wipe the case
occasionally with a damp cloth. DO NOT use
chemicals, cleaning solvents, or detergents.
Use only fresh batteries of the correct type.
Remove old or weak batteries so they do not
leak and damage the unit.
If the laser measurer is to be stored for long
periods, the batteries should be stored
separately to prevent damage to the unit.
CODE
CAUSE & CORRECTIVE ACTION
204
Calculation error. Repeat the
procedures in ‘OPERATION’.
208
Excessive current. Please contact
your distributor.
220
Battery low. Replace batteries.
253
Temperature too low. Warm up the
device.
255
Received signal is too weak or
measurement time is too long. Use a
target plate or a good reflective
surface.
MAINTENANCE
TROUBLESHOOTING
256
Received signal is too strong. The
target is too reflective. Use a target
plate or do not aim at a strong light
objective.
261
Outside of the range of
measurement. Select the
measurement distance within the
range of measurement.
500
Hardware error. Switch the device
On/Off several times. If the code still
appears contact your distibutor.
GENERAL MAINTENANCE
Recycle unwanted materials instead of disposing
of them as waste. All tools, hoses and packaging
should be sorted, taken to the local recycling
centre and disposed of in an environmentally
safe way.
Recycle rather than dispose of unwanted
material in landfill whenever possible. The
machine must be delivered in rigid packaging to
avoid damage during transportation. The
packaging and the machine itself are
manufactured from recyclable materials and
should be disposed of accordingly.
Only dispose of electrical/electronic/battery terms
in separate collection schemes, which cater for
the recovery and recycling of materials contained
within. Your cooperation is vital to ensure the
success of these schemes and for the protection
of the environment.
Recycle packaging where facilities exist.
This symbol is known as the Crossed
out Wheelie Bin Symbol. When this
symbol is marked on a product or
battery, it means that it should not be
disposed of with your general
household waste. Some chemicals contained
within electrical/electronic products or batteries
can be harmful to health.
Now that you have purchased your tool, should a
need ever exist of repair or service, simply
contact your nearest Ryobi Authorised Service
Centre or other qualified service organistion. Be
sure to provide all pertinent facts when you call
or visit.
Someof the following symbols may be used on
this product. Please study them and learn their
meaning. Proper interpretation of these symbols
will allow you to operate the product better and
safer.
Safety Alert Symbol. Indicates
danger, warning or caution. It means
attention! Your safety is involved.
Recycle Symbol.
Waste electrical
products should not be disposed
of with household waste. Please
recycle where facilities exist. Check
with your Local Authority or retailer
for recycling advice.
CE Marking. Conforms to relevant
safety standards.
Read the Instruction Manual. Your
manual contains special messages to
bring attention to potential safety
concerns as well as operating and
servicing information. Please read all
the information carefully to ensure
satisfaction and safe use.
Warning! Laser radiation.
RECYCLING AND DISPOSAL
SERVICE
SYMBOLS
1
7
5&6
1
2
3
4
INSTALLING THE BATTERIES
LASER RADIA
TION
Do not stare into beam!
CLASS 2 LASER
Max. output: <1mW
W
av
el
eng
th
: 63
0-
67
0n
m
IEC 60825-1
LASER DIST
ANCE MEASURER
000000000
Model: LDM-32, Battery: 2 x 1.5
AAA
Max measuring range: 0.2-30m
Ser
. No.
Made in China
