19
English(original instructions)
EN
FR
DE
ES
IT
PT
NL
SV
DA
NO
FI
HU
CS
RU
RO
PL
SL
HR
ET
LT
LV
SK
BG
■
To stop the motor, release the trigger and press
OFF
( O )
on the switch.
USING THE GUN/LANCE
See Figures 10 - 11.
For the most effective cleaning, the spray nozzle should
be between 20cm and 60cm from the surface to be
cleaned. If the spray is too close it can damage the
cleaning surface.
NOTE:
For greater control and safety, keep both hands
on the unit at all times.
Several different methods of cleaning are available.
Choose the method best suited for your cleaning project.
High Pressure Cleaning:
Squeeze the high pressure trigger on the gun. This will
provide a spray of water at high pressure.
When using the high pressure spray alone, detergent is
not dispensed.
Low Pressure (High Flow) Rinsing:
Move the low pressure (high flow) lever on top of the
trigger handle forward. This will provide a spray of water
at low pressure.
NOTE:
When using low pressure (high flow) rinsing only,
engage the high pressure trigger lock-out to prevent
accidental depressing of the high pressure trigger.
■
To dispense soap, turn the detergent dial to the ON
position.
■
To revert back to water only rinsing at low pressure,
turn the detergent dial to OFF.
Combination Cleaning/Rinsing:
To clean AND rinse the area with water at the same time
(for instance, in a heavily soiled area), move the low
pressure (high flow) lever forward and depress the high
pressure trigger.
■
To dispense detergent when using this combination,
turn the detergent dial to the ON position.
■
To rinse with no detergent using this combination,
turn the detergent dial to OFF.
NOTE:
Any cleaning or rinsing method using high
pressure spray requires that the on/off switch be in the
ON position.
For methods using low pressure only, the switch may be
in either the ON or OFF position.
USING THE NOZZLES
See Figure 12.
Before starting any cleaning job, determine the best
nozzle for the job. The 25
˚
nozzle is for general purpose
or large surfaces. The 0
˚
nozzle delivers a fine, powerful
jet used for spot cleaning or high-to-reach areas.
CAUTION
:
NEVER change nozzles without engaging the
lock out on the gun and NEVER point the lance
at your face or at others. The Quick Connect
collar contains small springs that could eject
the nozzle with some force. Failure to heed this
may cause personal injury.
Using the Quick Connect collar, changing nozzles is
easy.
To connect a nozzle to the lance:
■
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
■
Engage the lock out on the gun by pulling down on
the lock out until it clicks into the slot.
■
Push the nozzle into the Quick Connect collar until it
clicks in place and is secured properly.
To disconnect a nozzle from the lance once the
cleaning job is complete:
■
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
■
Engage the lock out on the gun by pushing down on
the lock out until it clicks into the slot.
■
Remove the nozzle by placing hand over nozzle then
pulling back the Quick Connect collar. Place nozzle in
the nozzle storage area .
To disconnect a nozzle from the trigger handle once
the cleaning job is complete:
■
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
■
Engage the lock-out on the trigger handle by pushing
up on the lock-out until it clicks into the slot.
■
Remove the nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place nozzle in
the nozzle storage area .
OPERATING THE PRESSURE WASHER
See Figures 13.
To clean:
■
Place the detergent dial in the ON position.
■
Start the pressure washer and spray the detergent on
a dry surface using long, even, overlapping strokes.
To prevent streaking, do not allow detergent to dry on
the surface.
■
Engage the high pressure trigger to clean the area.
■
Use a combination of high and low pressure (high
flow) for heavily soiled areas where constant flushing
is desired.
NOTE:
When using either high pressure or a combination
of high and low pressure (high flow), test a small area
first to avoid surface damage.
To rinse:
RPW120HS-25lgs.indd 19
RPW120HS-25lgs.indd 19
09-10-28 10:59
09-10-28 10:59
