manualshive.com logo in svg

Ryobi Expand-It ABCLT04G, Руководство оператора, Страница: 10 / 10

Поделиться
Скачать
Ryobi Expand-It ABCLT04G Скачать руководство пользователя страница 10

9

ENGLISH (Original Instructions)

maintenance  section.  For  other  repairs,  have  the  unit 

serviced by an authorised servicing dealer.

BLADE REPLACEMENT (Fig. 5)

■   Stop  the  engine,  place  the  holding  pin  (14)  through 

the slot in the upper flange washer (10) and the gear 

head (4). Turn the blade nut clockwise to remove the 

blade.

■   Place  the  upper  flange  washer  (10)  over  the  gear 

shaft with the hollow side towards the blade guard.

■   Centre  the  new  blade  on  the  upper  flange,  making 

sure the blade sits flat. Install the cupped washer (11) 

with the raised center away from the blade. Install the 

blade nut (12). The blade turns anticlockwise from the 

operator's position.

■   Place  the  holding  pin  through  the  slot  in  the  upper 

flange washer and the hole in the gear head. Using 

the spanner (13), turn the blade nut anticlockwise.

■   Tighten nut securely.

LINE HEAD REPLACEMENT (Fig. 7)

Installing the line head

■   Install  the  upper  flange  washer  onto  the  gear  shaft 

with the hollow side towards the gear head.

■   Place  the  holding  pin  throught  the  slot  in  the  upper 

flange washer and the hole in the gear head. Using 

the  16  mm  (5/8  in)  wrench  supplied,  turn  the  drive 

connector anticlockwise to install. Tighten securely.

ATTACHING THE STORAGE HANGER (Fig. 6)

There are two ways to hang your attachment for storage.

■   To  use  the  hanger  cap  (5),  push  in  the  button  (15) 

and  place  the  hanger  cap  over  the  end  of  the 

attachment shaft. Slightly rotate the cap from side to 

side until the button locks into place.

■   The secondary hole (16) in the attachment shaft can 

be used for hanging purposes as well.

WARNING

When  using  the  brush  cutter  blade,  the  grass 

deflector must be removed from the blade guard.  

When  using  the  line  trimmer  head,  the  grass 

deflector must be attached to the blade guard.

WARNING

Always  stop  the  engine  and  remove  the  spark 

plug wire before making any adjustments such 

as changing cutting heads; this is to reduce the 

risk of serious personal injury.

20120622v1

Содержание Expand-It ABCLT04G











Отзывы:

Нет отзывов