background image

2

English

 

Keep cutting tools sharp and clean. Properly 
maintained cutting tools with sharp cutting edges are 
less likely to bind and are easier to control.

 

Use the power tool, accessories and tool bits etc. in 
accordance with these instructions, taking into account 
the working conditions and the work to be performed. 
Use of the power tool for operations different from 
those intended could result in a hazardous situation.

SERVICE

 

Have your power tool serviced by a qualified repair 
person using only identical replacement parts. This will 
ensure that the safety of the power tool is maintained.

 

If the supply cord is damaged, it must be replaced 
by the manufacturer, its service agent or similarly 
qualified persons in order to avoid a hazard.

SPECIAL SAFETY RULES

 

Recommendation for the use of a residual current 
device with a rated residual current of 30 mA or less.

 WARNING

This product is not intended for use by persons 
(including children) with reduced physical, sensory 
or mental capabilities, or lack of experience and 
knowledge, unless they have been given supervision or 
instruction concerning use of the product by a person 
responsible for their safety.

Children should be supervised to ensure that they do 
not play with the product.

SPECIFICATIONS

Voltage 

220 V - 240 V   50 Hz

No-load speed

30,000 min-

1

Input power

350 W

Max. cutter diameter

6.35 mm

Weight

1.75 kg

APPLICATIONS

You may use the trimming and routing kit for the purposes 
listed below:

 

Routing all types of timber.

 

Cabinet making, trimming counter tops and finishing 
work.

 

Trimming wood and plastics.

ASSEMBLY

 WARNING

Your trimming and routing kit should never be 
connected to a power supply when you are assembling 
parts, making adjustments, installing or removing 
cutters, or when not in use. Disconnecting your trimmer 
will prevent accidental starting that could cause serious 
injury.

 WARNING

Do not use cutters with undersized shanks. Undersized 
shanks will not tighten properly and could be thrown 
from tool causing injury.

 WARNING

Do not use cutters that are larger in diameter than the 
opening in trimmer base. Use of such cutters will come 
in contact with the trimmer base and damage both 
the cutter and trimmer base. Possible loss of control 
or create other hazardous conditions that could cause 
possible serious personal injury.

INSTALLING/REMOVING CUTTERS

See fi gure 2

 WARNING

Failure to unplug your trimmer could result in accidental 
starting causing serious injury.

 

Unplug your trimmer.

 

Place your trimmer upside down on a workbench in 
order to gain easy access to the spindle and collet nut.

 

Place the small end of one of the wrenches provided on 
the spindle flats. This will hold the spindle stationary.

 

Place the large end of the other wrench provided onto 
the collet nut. Rotate wrench counterclockwise to 
loosen collet nut.

Содержание EVT350RG













Отзывы: