6
n
TOOL SERVICE MUST BE PERFORMED ONLY
BY QUALIFIED REPAIR PERSONNEL.
Service or
maintenance performed by unqualified personal could
result in a risk of injury.
n
WHEN SERVICING
use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
n
ALWAYS STAY ALERT!
Do not allow familiarity (gained
from frequent use of your tool) to cause a careless
mistake.
ALWAYS REMEMBER
that a careless fraction
of a second is sufficient to inflict severe injury.
n
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation
BEFORE
performing any work using your
tool.
n
ALWAYS TURN OFF THE TOOL
before disconnecting it
to avoid accidental starting when reconnecting to power
supply.
NEVER
leave the tool unattended while connected
to a power source.
n
DO NOT OPERATE IN POOR
LIGHTING.
Use the unit
only in daylight or good artificial light.
n
KEEP ALL BYSTANDERS
especially children and pets,
at least 3m from the operating area.
n
PULL THE PLUG OUT IMMEDIATELY
if the mains or
extension lead is damaged or severed.
n
DO NOT ALLOW
anyone to operate the log splitter who
has not read the operator’s manual or has not been
instructed on the safe use of the splitter.
n
NEVER ALLOW CHILDREN OR UNTRAINED ADULTS
TO OPERATE THIS MACHINE.
n
IF SOMEONE
is helping load logs to be split,
DO NOT
start the machine until that person is clear of the area.
n
NEVER ALLOW ANYONE TO RIDE ON THE
MACHINE.
n
NEVER TRANSPORT ANYTHING OR ANYONE ON THE
LOG SPLITTER.
n
HIGH FLUID PRESSURES ARE DEVELOPED IN
HYDRAULIC LOG SPLITTERS.
Pressurized hydraulic
fluid escaping through a pin hole opening can puncture
skin and cause severe blood poisoning. Heed the
following instructions at all times:
a) Do not operate the machine with frayed, kinked,
cracked, or damaged hoses, fittings, or tubing.
b) Stop the engine and relieve hydraulic system pressure
before changing or adjusting fittings, hoses, tubing,
or other system components.
c) Do not adjust the pressure settings of the pump or value.
d) Never use your hand. Leaks can be located by
passing cardboard or wood over the suspected area.
Look for discoloration. If injured by escaping fluid,
see a doctor at once. Serious infection or reaction can
develop if proper medical treatment is not adminis-
tered immediately.
n
KEEP THE OPERATOR ZONE
and adjacent area clear
for safe, secure footing.
n
LOG SPLITTERS SHOULD BE USED ONLY
for splitting
wood. DO NOT use for other purposes unless the
manufacturer provides attachments and instructions.
n
MAKE SURE THE LOG SPLITTER
is on a level surface.
Block the splitter as required to prevent unintended
movement.
n
ALWAYS OPERATE
the splitter from the indicated
operator zone.
n
LOGS TO BE SPLIT ON RAM-TYPE UNITS
should be
cut as squarely as possible.
n
THE MACHINE OWNER
should instruct anyone assisting
him or her in safe log splitting operation.
n
ALWAYS
operate the log splitter with all safety equipment
in place and all controls properly adjusted for safe
operation.
n
ALWAYS
operate the log splitter at the recommended
speed.
n
WHEN LOADING
a ram-type log splitter, place your
hands on the sides of the log not at the ends.
NEVER
place your hands or any part of your body between a log
and any part of the log splitter.
n
ON RAM-TYPE
log splitters,
NEVER
attempt to split
more than one (1) log at a time unless the ram has been
fully extended and a second log is needed to complete
the separation of the first log.
n
ON RAM-TYPE
log splitters on which the logs are not
square, the longest portion of the log should be rotated
down and the most square end placed against the ram.
n
CLEAR DEBRIS
from moving parts but only when the
power source is shut off.
n
USE ONLY YOUR HAND TO OPERATE THE LOG
SPLITTER CONTROLS.
n
ALWAYS UNPLUG FROM THE POWER SOURCE
while
repairing or adjusting the splitter .
n
CIRCUIT CAPACITY AND FUSES:
a) Use only an electrical circuit having adequate capacity.
b) “Blowing” a fuse or tripping a circuit breaker is usually
a warning that you are overloading the machine or
have too many devices taking power from the circuit,
or both. Do not install a higher capacity fuse!
n
LEARN AND UNDERSTAND
all controls and the proper
use of the equipment.
n
SAVE THESE INSTRUCTIONS.
Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions also.
GENERAL SAFETY RULES
SPECIFIC SAFETY RULES
WARNING!
“Danger! Keep clear of moving parts!”
“To be operated by one person only!”
ENGLISH (Original Instructions)
