![background image](http://html.mh-extra.com/html/ryobi/ehg2000/ehg2000_original-instructions-manual_1505743004.webp)
Safety
2
protect and retain hair.
■
Make sure you are always well balanced when using
the heat gun.
■
Ensure that the heat gun is always clean, dry and free
from oil or grease.
■
Never force the tool or accessories, and only use them
for the purpose for which they are designed.
■
Always keep the heat gun upright or suspend it with the
stand supplied.
■
Never use the heat gun in a damp or very wet area (for
example: bathrooms, saunas).
■
Never leave the heat gun out in the rain and do not use
it on very damp days.
■
Never push anything down inside the hot air nozzle.
■
Always allow the heat gun to cool down completely
before storing it.
■
Always store the heat gun in a safe place, out of the
reach of children. It is not a toy.
■
This device shall connect to such power supply network
with impedance equal to or less than 0.063 + j0.039
Ω
or the agreement with power supplier or user. Any
mismatched connection may cause high voltage
fluctuation.
■
A fire may result if the product is not used with care,
therefore:
–
be careful when using the product in places where
there are combustible materials;
–
do not apply to the same place for a long time;
–
do not use in presence of an explosive atmosphere;
–
be aware that heat may be conducted to combustible
materials that are out of sight;
–
place the product on its stand after use and allow it
to cool down before storage;
–
do not leave the product unattended when it is
switched on.
■
Check the area where the heat gun is to be used.
Behind ceilings, floors and false ceilings may contain
highly flammable material. Always check these before
using the heat gun.
■
Keep the work area clean and uncluttered.
■
Keep the work area well lit.
■
Keep children and visitors away from the work area,
heat gun and any extension cables.
■
To reduce the risk of electric shock, please wear proper
shoes to avoid contact with earthed surfaces.
■
Never carry the heat gun by its power cable or pull on
the cord to disconnect it.
■
Use only suitable extension cables.
■
Inspect the heat gun cable regularly and if damaged,
have it repaired by authorized service centre.
■
When the heat gun is used outdoors, use only extension
cables that are suitable for exterior use.
■
When working on small or irregular shaped objects,
clamp the object in a vice or clip.
■
Ensure the tool switch is at off position before plugging
in.
■
Disconnect the heat gun when it is not in use. Ensure
that the heat gun cannot start accidentally. If the heat
gun stops while it is in use, disconnect it from the power
supply and have it serviced by authorised service
centre.
WARNING
Always concentrate on the job and use common sense
when working with this or any other tools. Do not use this
tool when you are tired or taking medication that may
make you drowsy.
NOTE:
Keep the nozzle at least 10 cm away from the
working surface. Heat guns have a safety cut-off which will
stop the heat gun if you are working too close to the surface
being stripped. If the cut-off operates, the heat gun must
be allowed to cool for about 30 minutes before it can be
used again.
■
Never use the heat gun in combination with solvents.
■
After use, remove any paint or varnish residue on the
nozzle and scrapers. This could catch fire.
■
Always work in a well ventilated area. Flakes and
residues of lead-based paints are highly toxic.
SPECIAL SAFETY RULES
■
This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
product by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the product.
■
Keep children and visitors away.
Visitors should wear
safety glasses and be kept as a safe distance from work
area. Do not let visitors contact tool or extension cord.
■
It is recommended that this tool always be supplied via
a residual current device with a rated residual current
of 30mA or less.
INTENDED USE
You may use this product for the purposes listed below:
■
Shrink fitting
■
Bending plastic pipes
■
Thawing frozen pipes
■
Softening adhesives
■
Soft soldering
■
Paint stripping
Содержание EHG2000
