background image

9

ENGLISH

TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

Machine does not start

1. Power cord not plugged in.

2. Power cord is damaged. 

3. Circuit breaker is tripped. 

4. Circuit fuse is blown. 

5. Switch is damaged or burned out.

1. Plug in cord.

2. Have the cord replaced at your 

nearest authorized service centre.

3. Reset circuit breaker.

4. Replace circuit fuse.

5. Have the switch replaced at your 

nearest authorized service centre. 

Motor does not reach full speed or 

power.

1. Voltage from power source is low.

2. Circuit is overloaded. 

3. Motor burned out.

4. Fuses or circuit breakers are 

wrong size.

5. Extension cord is too long.

6. Switch is defective.

1. Request a voltage check up.

2. Test on a different circuit or without 

anything else on circuit.

3. Have tool serviced and request a 

voltage check.

4. Have an electrician replace with a 

wrong size. circuit breaker.

5. Use a shorter extension cord.

6. Have the switch replaced at your 

nearest authorized service centre.

Motor stalls, blows fuses, or trips 

circuit breakers.

1. Switch is defective. 

2. Voltage from source is low. 

3. Fuses or circuit breakers are 

wrong size or defective.

1. Have the switch replaced at your 

nearest authorized service center.

2. Request a voltage check.

3. Have an electrician replace with a 

circuit breaker.

Motor overheats. 

1. Motor is overloaded.

2. Wheel is being fed into work too 

fast.

1. Request a voltage check.

2. Feed wheel into work slower.

Machine is noisy when running. 

1. Motor needs attention. 

1. Have the motor checked at your 

nearest authorized service centre

Wheel hits table.

1. Wheel not properly installed. 

2. Depth stop setting incorrect. 

1. See “Removal and Installation of 

Wheel” section.

2. Adjust the depth stop. See “Depth 

Stop” section.

 

   

 

   

   

 

   

 

Содержание ECO2437

















Отзывы: