background image

4 — English

SYMBOLS

CALIFORNIA PROPOSITION 65

WARNING:

 

This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may 

contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive 

harm. 

Wash hands after handling.

Some examples of these chemicals are:

•  lead from lead-based paints,
•  crystalline silica from bricks and cement and other masonry products and,
•  arsenic and chromium from chemically treated lumber. 

Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your 

exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially 

designed to filter out microscopic particles. 

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation 

of these symbols will allow you to operate the product better and safer.

SYMBOL

NAME

DESIGNATION/EXPLANATION

Safety Alert

Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand 

operator’s manual before using this product.

Wear Eye Protection

Always wear eye protection with side shields marked to comply 

with ANSI Z87.1.

Wet Conditions Alert

Do not expose to rain or use in damp locations.

V

Volts

Voltage

A

Amperes

Current

Hz

Hertz

Frequency (cycles per second)

min

Minutes

Time

Alternating Current

Type of current

no

No Load Speed

Rotational speed, at no load

Class II Construction

Double-insulated construction

.../min

Per Minute

Revolutions, strokes, surface speed, orbits etc., per minute

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL

SIGNAL

MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result 

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result 

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in 

minor or moderate injury. 

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an 

injury hazard, such as a situation that may result in property damage.

Содержание D620H

































Отзывы: