3
WARNING
:
Read and understand all instructions.
Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
n
Keep your work area clean and well lit.
Cluttered
benches and dark areas invite accidents.
n
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust.
Power tools create sparks which may ignite the
dust or fumes.
n
Keep bystanders, children, and visitors away while
operating a power tool.
Distractions can cause you to
lose control.
ELECTRICAL SAFETY
n
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
n
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators.
There is an
increased risk of electric shock if your body is ground-
ed.
n
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
n
Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately.
Damaged cords
increase the risk of electric shock.
n
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”.
These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
n
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication.
A moment of inattention while operating
power tools may result in serious personal injury.
n
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts.
Loose clothes, jewelry, or long
hair can be caught in moving parts.
GENERAL SAFETY RULES
n
Avoid accidental starting. Be sure switch is off before
plugging in.
Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites acci-
dents.
n
Remove adjusting keys or wrenches before turning
the tool on.
A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
n
Do not overreach. Keep proper footing and balance
at all times.
Proper footing and balance enables better
control of the tool in unexpected situations.
n
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
n
Do not wear loose clothing or jewelry. Contain long
hair.
Loose clothes, jewelry, or long hair can be drawn
into air vents.
n
Do not use on a ladder or unstable support.
Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
n
Use clamps or other practical way to secure and sup-
port the workpiece to a stable platform.
Holding the
work by hand or against your body is unstable and may
lead to loss of control.
n
Do not force tool. Use the correct tool for your appli-
cation.
The correct tool will do the job better and safer
at the rate for which it is designed.
n
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
n
Disconnect the plug from power source before mak-
ing any adjustments, changing accessories, or storing
the tool.
Such preventive safety measures reduce the
risk of starting the tool accidentally.
n
Store idle tools out of the reach of children and other
untrained persons.
Tools are dangerous in the hands of
untrained users.
n
Maintain tools with care. Keep cutting tools sharp
and clean.
Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
n
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using.
Many accidents are caused by
poorly maintained tools.
n
Use only accessories that are recommended by the
manufacturer for your model.
Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
n
Keep the tool and its handle dry, clean and free from
oil and grease.
Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Fol-
lowing this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
