Ryobi BPL3626D, Оригинальное руководство пользователя, Страница: 3 / 8

2
1
2
1. LED
2. Fuel gauge button
BATTERY PROTECTION FEATURES
Ryobi 36V LITHIUM-ION batteries are designed with
features that protect the LITHIUM-ION cells and maximise
battery life. If the tool stops during use, the following may
be the causes:
a. The maximum current draw of the battery has been
exceeded, causing it to automatically stop powering
the tool. Release the trigger to reset the tool and pull
the trigger to resume operation.
b. Excessive temperatures will cause the battery to
stop powering the tool. Feel the battery pack; if it is
too warm, allow it to cool down.
If the tool still does not work, recharge the battery.
NOTE: The battery pack indicator LED will not work if the
battery protection feature has caused the battery pack to
stop powering the tool. Release the tool trigger or remove
the battery pack from the tool and the battery pack LED
indicator will resume normal function.
CHARGING THE BATTERY PACK
Battery packs are shipped in a low charge condition to
prevent possible problems. Therefore, you should charge
them until the green LED on the front of the charger comes
on.
If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Authorised Service Center for
electrical check.
TO CHARGE
■ Use battery pack only with the recommended charger.
■ Connect the charger to the power supply. Make sure
the power supply is normal household voltage, 220-240
volts, AC only, 50 Hz.
■ Make sure the latch of the battery pack snap into place
and the battery pack is secured in the charger before
beginning operation.
■ Slide the battery pack along the groove of the charger.
■ Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
■ Do not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
■ NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 10°C
but less than 38°C.
■ The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
■ After charging is complete, the charger green LED
will remain on until either the battery pack has been
removed from the charger or the charger has been
removed from the power supply.
■ After charging is complete, the battery pack indicator
LED will remain on 1 min then turn off. But if the battery
pack has been removed from the power supply, the
battery pack indicator LED will turn off.
■ When batteries become fully charged, unplug the
charger from the power supply and remove the battery
pack.
■ To remove the battery pack from the charger, depress
the latch of the battery pack.
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the
red LED will begin
fl ashing and the green LED will be off.
When the battery pack cools down to approximately 50°C,
the charger will automatically begin fast charge mode.
CHARGING A COOL BATTERY PACK
If the battery pack is below normal temperature range, the
red LED will begin
fl ashing and the green LED will be off.
When the battery warms to a temperature of more than
0°C, the charger will automatically begin charge mode.
COLD WEATHER OPERATION
The LITHIUM-ION battery pack can be used in temperatures
down to -20°C. Put the battery pack on a tool and use the
tool in a light duty application. After about a minute, the
pack will have warmed up and begin operating normally.
BATTERIES
These batteries have been designed to provide maximum
trouble-free life. However, like all batteries, they will
eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
To obtain the longest possible battery life, we suggest the
following:
■ Remove the battery pack from the charger once it is
fully charged and ready for use. For battery pack
storage longer than 30 days:
● Store the battery pack where the temperature is
below 27°C and away from moisture.
● Store battery packs in a 30%-50% charged
condition.
● Every six months of storage, run battery with a tool
until cut off by pack’s program control. Then charge
the pack as normal.