background image

- 5 -

DESCRIPTION

  1. Charging indicator 

2. Safety switch

  3. on/off switch 

4. Bottom cover

  5. Hedge trimmer blade 

6. Charger 

  7. Grass shear blade 

8. Charger jack

  9. Charging socket

SPECIFICATIONS

Input  ………………………………… 230V ~ 50 Hz  9W

Output………………………………… 12V d.c. 300mA

Charger type ………………………… SH-7.2V300

Charging time  ……………………… 3 ~ 5 hours (approx) 

Battery type  ………………………… Li-ion

Battery capacity  …………………… 1300 mAh

No load speed  ……………………… 1000 min

-1

Cutting width  (Hedge trimmer) …… 120 mm

 

(Grass shear)  ……… 100 mm

Net weight  (Hedge trimmer) …… 0.8 kg

 

(Grass shear)  ……… 0.7 kg

STARTING AND STOPPING (Fig.1)

To start your Hedge Trimmer and Grass Shear

Push the safety switch (2) on either side and depress the on/off 

switch (3).

To stop your Hedge Trimmer and Grass Shear

Move hedge trimmer away from cutting area before stopping. To 

stop, release on/off switch.

NOTE:

 the tool can not be switched on while the on/off switch is 

depressed only. 

BEFORE USE

WARNING! 

Always ensure that the tool is switched off and 

totally stop before operation.

1. REPLACING THE CUTTING BLADE 

CAUTION:

 Always wear work gloves when replacing a blade.

Install the blade ( Fig.2 , 3 , 4 )

Mounting blade

  1.  Press the clip on the bottom cover (4) and pull along the 

direction mark, and remove the bottom cover from the tool.

  2.  Align the mark on the housing (A) and gear (B).

  3.  Align the marks on the fixed blade (C) and movable blade (D).

  4.  Position the two holes on the blade to the two pins on gears, 

and push the blade until it is fit into the housing. 

  5.  Place the bottom cover on the tool and push the clip on it 

until the clip firmly locks to the tool.

Replacing blade

Remove the bottom cover in the same way as mounting blade, 

and then change the blade to which you require. Place back the 

bottom cover, and make sure it is fixed firmly to the tool.

2. CHARGING THE BATTERY ( Fig. 5 )

CAUTION:

 For indoor use only. Charge only with supplied charger.

Your tool is delivered to you partly charged and must be fully 

charged before use. For the first charge we recommend charging 

for 10~12hours. 

To charge, plug the charger jack (8) into the charging socket (9) 

and place the tool onto a clean dry surface.

Connect the charger to a suitable power point. The upper lamp 

will light up “RED” while you charging the tool and all three (3) 

lamps will light up GREEN after it becomes fully charged. While 

you operating the tool, all three (3) lamps lighting up GREEN 

means battery is full. The lamps will go off one by one as battery 

is exhausted, and the upper lamp will light up RED when battery 

becomes almost empty.

The charging time is approximately 3~5hours.

Disconnect the charger from the power point when battery is full 

charged.

NOTE: 

Whilst charging, the charger and the tool may become 

warm to touch, this is normal and does not indicate problem. 

Disconnect the charger from the power point when it is not in use 

and store it in a dry secure place.

WARNING:

 It is important to disconnect the charger from the 

power point after the battery is fully charged. Do not leave your 

battery on charge continuously as this may damage the battery.

Avoid operating, charging or storing your battery in temperatures 

below 0°C and above 40°C.

OPERATION

CAUTION :

  Always wear eye protection.

1. Shearing ( Fig. 6 )

Remove all stones or other objects from within the working area.

Push the safety switch forward and depress the on/off switch.

Put down the device horizontally with your hand, and the blade 

should touch the ground. Results are best when the lawn is dry.

NOTE:

 make sure there is no hard obstacle in the working area, 

such like stone etc. or the blade will be damaged. 

2. Trimming  ( Fig. 7 )              

The device may be used to trim small hedges and shrubs. 

Hold the device in a slight angle to the hedge you would like to 

trim.

Trim the lateral areas from the lower to the upper edges first, and 

then trim the upper edge.

NOTE:

 wear safety goggles and eye protection to avoid accident.

MAINTENANCE AND REPAIR 

WARNING! 

Always ensure that the tool is switched off and 

totally stop before making any adjustments or maintenance 

procedures.

---  Never use water to cleaning the unit. 

---  Always clean the grass shear immediately after use. Brush 

the blade using a stiff nylon brush to remove any debris. 

Wear safety glasses to protect your eyes whilst cleaning.

---  Always store the unit in a dry place.

---  Inspect the grass shear before each use.

---  Have the unit professionally repaired if any damage occurs.

---  The blade rail should be cleaned and treated with fine oil 

after each use.

---  Use the blade guard for transportation and storage.

---  Regularly check that all the fixing screws are tight. They 

may vibrate loose over time.

---  Keep the tool’s cooling vents unclogged and clean at all 

times. 

---  Regularly check to see if any dust or foreign matter has en-

tered the grills near the motor and around the switches. 

---   If the body of the tool needs cleaning, wipe it with a soft 

damp cloth. A mild detergent can be used but nothing like 

alcohol, petrol or other cleaning agent.

Отзывы: