7
wARnIng
Always wear eye protection with side shields. Failure
to do so could result in objects being thrown into your
eyes resulting in possible serious injury.
wARnIng
Always release all pressure, disconnect from power
supply, and allow unit to cool before cleaning or making
repairs on the air compressor.
geneRAL mAIntenAnce
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
As a routine part of air compressor maintenance, it is also
advised that the oil is routinely checked for proper levels.
wARnIng
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Bearing lubrication
All of the bearings in this product are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore, no
further lubrication is required.
RePLAcIng AIR fILteR
See figure 16.
1.
Loosen the wing nut and washer on the air filter cover.
2. Remove the cover.
3.
Remove the air filter.
4.
Install new air filter.
5.
Replace the air filter cover and secure it with the wing
nut and washer.
RePLAcIng oIL
See figure 17.
wARnIng
The hot oil can surface can scald or burn your hands.
Allow the compressor to cool 15 minutes before
removing the drain plug and draining the oil.
Replace the oil after the first 10 hours of operation and
every 100 hours following the first oil change.
The sight glass indicates the oil level and lets the operator
check if oil should be added.
1. Place a suitable container underneath the drain to
collect used oil.
2. Remove the drain plug using a wrench.
3. When the used oil has drained, reinstall the drain plug
and tighten with the wrench.
4.
Unscrew the cap of oil fill hole.
5.
To refill, use a funnel to pour oil into the fill hole. Refill
only with synthetic oil SAE-30.
note:
Avoid refilling with too much oil. Ensure that the
level of the oil does not exceed the top of the red dot at
sight glass. The recommended amount of oil for refilling is
280 ml (8.11 oz.).
6.
Tighten the cap securely into the oil fill hole.
envIRonmentAL PRotectIon
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
symBoLs
Safety Alert
Please read the instructions carefully
before starting the machine.
Wear ear protection
Wear eye protection
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
Regulatory Compliance Mark (RCM).
Product meets applicable regulatory
requirements.
Caution, risk of electric shock
Содержание Airwave RA-C2550-G
