Ryobi 0177344, Оригинальное руководство пользователя

Страница: 7 / 12

5
See Fig.3
4. Disconnect the product from the power supply when the
battery pack becomes fully charged.
5. Press the battery pack latch to unlock the battery pack
from the product.
6. Slide the product off the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the cells in the battery
pack becomes hot. A hot battery pack should be cooled
down for approximately 30 minutes before recharging.
CHARGING A USB DEVICE
When the product is connected to an AC power supply or
a battery pack, the USB port on the product supplies a 5
volt DC, up to 2.1 amp charging site for your phone, MP3
player, or other small (up to 2.1 amp) USB device.
Using an AC power supply
See Fig. 4
1. Connect the power cable to the charger. Plug the USB
cable into the product and into your USB device.
2. Connect the power adaptor to a power source.
NOTE: The LED will turn red and remain on for
approximately 5 minutes when the product is connected
to an AC power supply and not installed on a battery
pack.
NOTE: The USB port on the product is always active
when the device is connected to an AC power supply.
The USB device will begin charging as soon as it is
connected to the charger. It is not necessary to press
the ON button.
3. The product will provide continuous charging to the
USB device until the device is fully charged.
4. Remove the device when charging is complete.
Using a battery pack
See Fig. 5
1. Remove the cable from the product, then remove the
power adaptor from the power source and store in a
cool, dry location.
2. Connect the product to a charged battery pack.
NOTE:
When the product is connected to a battery
pack only, the LED will remain off until the ON button
is pressed.
3. Plug the USB cable into the product and into your USB
device.
4. Press the ON button to start charging the USB device.
NOTE: If the product stops providing power to the USB
device before it is fully charged, the battery pack may
have entered “sleep mode”. Press the ON button to exit
“sleep mode” and resume operation.
NOTE : “Sleep mode” is a feature that protects the
battery from becoming fully drained. It stops charging
the USB device after 30 seconds if the charging current
is less than 30 mA.
NOTE: USB charging time is dependent upon the level
of charge in the USB device when it is connected to the
charger. When a USB device is charging, energy from
the battery pack is transferred to the USB device. If the
energy in the battery pack is depleted, USB charging
will stop.
NOTE: USB charging will stop once the device is fully
charged.
MAINTENANCE
■ When not using or when cleaning the product,
disconnect it from the power supply and remove the
battery pack.
■ Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloth or soft brush to remove dirt and dust.
■ Do not, at any time, let brake fluids, gasoline, petroleum-
based products, and penetrating oils come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
■ If you are experiencing any issues with this product or
any other RYOBI product, contact RYOBI Customer
Service.
WARNING
Hazardous voltages are present within the product; do
not disassemble.
■ The supply cord cannot be replaced. If the
cord is damaged, the product should be
scrapped.
CLEANING THE CHARGER
WARNING
Unplug the charger power cord from power supply
before cleaning at any time to prevent serious personal
injury.
■ Clean the charger surface (except labels) using a damp
cloth with a mild detergent.
■ Do not use any strong detergents on the plastic housing.
They can be damaged by certain aromatic oil such as
pine and lemon, and by solvents such as kerosene.
■ Moisture can cause a shock hazard. Wipe off any
moisture with a soft dry cloth.
STORAGE
STORAGE
Store your charger in a cool dry place between 10 and
38°C.