Rycom 8879 Скачать руководство пользователя

Страница: 20 / 24

Set the R

ECEIVER

to the S

ONDE

mode by holding the shift key while pressing the Depth Button). Next, hold

the R

ECEIVER

antenna directly above and in line with the S

ONDE

, as shown below. The R

ECEIVER

sensitivity

needs to adjusted for a meter reading indication between 60% to 80%.

The radiation pattern of the S

ONDE

is shown below. The PEAK signal is when the R

ECEIVER

is held directly

over the S

ONDE

with the antenna in line with the S

ONDE

. Both behind and in front of the S

ONDE

ghost sig-

nals can be located. By locating the ghost signals, the user is confirming the accuracy of the locate.

Locating a Sonde

Start by following the suspected path of the pipe and use the 8879 R

ECEIVER

to locate the S

ONDE

. Stop locat-

ing when the PEAK reading is found. Then rotate the R

ECEIVER

as shown in the figure below. When pivot-

ing the R

ECEIVER

, do not change the vertical position. The R

ECEIVER

will indicate a PEAK when the R

ECEIVER

antenna is in line with the S

ONDE

Now move the R

ECEIVER

side to side (across the path of the pipe) as shown below. When the PEAK if found,

the R

ECEIVER

is directly over the S

ONDE

. Mark this location. Next, check for ghost signals in front of and in

back of the S

ONDE

to confirm thE location.

FEED THE SONDE 10 FEET (3 METERS) INTO THE PIPE

Содержание 8879

























Результаты поиска

Содержание 8879

Отзывы:

Похожие инструкции для 8879

Бренды по названию

Популярные бренды

Rycom 8879, Руководство пользователя

Результаты поиска

Содержание 8879

Отзывы:

Похожие инструкции для 8879

Бренды по названию

Популярные бренды