Russound CAM6.6T-S1 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 112

background image

23

INSTALLER

WIRING INSTRUCTIONS

RJ-45 Connections

The CAT-5 T568A wiring standard shown on
the right is used for the RJ-45 terminations.

Keypad Wiring

For the UNO-S1 keypad, the following connec-
tions are used to terminate the CAT-5 wire to the
110 punchdown on the keypad:

CAT-5 WIRE COLOR

TYPE

Brown . . . . . . . . . . . . . . . . . . . +12V

Brown/White . . . . . . . . . . . . . . +12V

Green . . . . . . . . . . . . . . . . . . Ground

Green/White . . . . . . . . . . . . Status In

Orange . . . . . . . . . . . . . . . . . Ground

Orange/White . . . . . . . . . . . . . IR Out

Blue . . . . . . . . . . . . . . . . . . . COM A

Blue/White . . . . . . . . . . . . . . COM B

• To determine the amount of CAT-5 wire
required for the system installation, first
decide how many keypads will be used, then
determine the distance between each intend-
ed keypad location to the intended CAM6.6
location. The maximum recommended wire
run length is 250 feet for each UNO-S1
Keypad.

• Make sure that the entire wire path
between keypads and CAM6.6 is clear and
not obstructed by a floor ceiling joist, or
masonry wall which can’t be drilled through.

• Confirm ahead of time that you can drill an
outlet hole easily and in an unobtrusive spot
to connect wires with the CAM6.6.

• Label wires with keypad and room location.
This simplifies CAM6.6 hook-up once the key-
pads and speakers are installed.

Speaker Wiring

Standard 16-gauge 4-conductor stranded
speaker wire can be run up to to 125 feet;
14-gauge wire can be run up to 250 feet.

When running wire, pay particular attention to
the following areas:

• Avoid locations concealing pipes, heating
ducts and AC wiring in the general vicinity.

• Avoid running wires close to house electri-
cal wiring for any distance. If you have to run
them parallel, make sure to space the wires
at least two feet from the AC line.

«
...
21
22
23
24
25
...
»

Содержание CAM6.6T-S1

















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6T-S1

Бренд: NAD Страницы: 2

Бренд: Alinco Страницы: 48

Бренд: Axxera Страницы: 32

Бренд: PCB Piezotronics Страницы: 17

Бренд: Teac Страницы: 4

Бренд: Goodmans Страницы: 16

Бренд: Rock Mars Страницы: 18

SoundPlus Infrared Receiver WIR RX12-4

Бренд: Williams Sound Страницы: 2

EasyListener2 230R

Бренд: Phonic Ear Страницы: 53

Бренд: Alinco Страницы: 37

Бренд: Power Acoustik Страницы: 78

Бренд: AFi Страницы: 8

Бренд: MultiDyne Страницы: 8

Therm RF Series

Бренд: Boss Страницы: 2

Бренд: Planet Audio Страницы: 25

Бренд: C4Line Страницы: 2

Бренд: Dahua Technology Страницы: 13

Бренд: Cobra Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды