Russound CAM6.6T-S1 Скачать руководство пользователя страница 19

Страница: 19 / 112

USER

INTERNAL SOURCE - AM/FM TUNER

UNO-LRC1 Remote Control

POWER - Power managed by CAM6.6

NUMERIC INPUT - (press) Number buttons for
direct input of frequency, preset, bank

MEMORY PRESETS - (press and hold) Number
buttons (1-6) for saving memory presets

TUNE UP/DOWN - Incrementally scrolls through
tuned stations

TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations

SELECT - Confirms numeric selection

PLAY - Selects AM or FM band

BANK UP/DOWN - (press and hold) Used for bank
selection

MEM UP/DOWN - (press) Scrolls through memory
presets for selected bank

MUTE - Mutes/unmutes tuner audio output

SCAN - (press and hold) Scans through tuned sta-
tions with 5-second preview before next station

SEEK UP/DOWN - (press) Seeks next tuned sta-
tion up or down

TUNER SELECTION - Select source number
assigned to TUNER 1 or TUNER 2

SEEK UP/DOWN - Seeks next tuned station up or
down

UNO SELECTION - UNO must be the
selected source for control of the
CAM6.6 and any connected compo-
nents. Select UNO before sending
UNO-LRC1 remote commands.

Содержание CAM6.6T-S1

















































































































Результаты поиска

Содержание CAM6.6T-S1

Отзывы:

Похожие инструкции для CAM6.6T-S1

Бренды по названию

Популярные бренды

Russound CAM6.6T-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6T-S1

Отзывы:

Похожие инструкции для CAM6.6T-S1

Бренды по названию

Популярные бренды