background image

 

14. Snatch Block: If your winch is supplied with a snatch block that can double the 

pulling power of the winch, or change the pulling direction without damaging the 

wire rope. We recommend you to use double line and snatch block for pulling 

over 70% of the rated line pull. 

SAFETY PRECAUTIONS 

WARNING

 

WARNING 

– 

Do not exceed rated capacity shown in this table. 

WARNING 

 Intermittent use only.  Allow winch to cool between uses.

 

WARNING 

– 

 Do not use winch to lift (vertically).

 

WARNING 

– 

  Do not use winch to pull or move people in any way.

 

WARNING 

– 

NEVER cut, weld, or modify any part of the winch or cable.

 

WARNING 

– 

A  minimum  of  five  wraps  of  cable  around  the  drum  barrel  is 

necessary for pulling and holding the rated load.  

WARNING 

– 

Keep yourself and others a safe distance to the side of the cable 

when it is under tension.

 

WARNING 

– 

The  wire  rope  may  break  before  the  motor  stalls.    For  heavy 

loads  at  or  near  rated  capacity,  use  a pulley  block/snatch  block  to  reduce  the 

load on the wire rope. 

WARNING 

– 

Never step over a cable, or go near a cable under load. 

WARNING 

– 

Don’t move the vehicle to pull a load (towing) on the winch cable.  

This could result in cable breakage. 

WARNING 

– 

Disconnect the remote control and battery leads when not in use. 

WARNING 

– 

Avoid “shock loads” by using the control switch intermittently to 

take  up  the  slack  in  the  wire  rope.    “Shock  loads”  can  far  exceed  the  rate 

capacity for the wire rope and drum. 

WARNING 

–  

Do not exceeds maximum line pull ratings shown on the tables.

 

WARNING 

– 

When  re-spooling  the  cable  ensure  that  the  cable  spools  in  the 

under-wind  position  with  the  cable  entering  the drum  from  the  bottom,  not  the 

top.      To  spool  correctly  you  should  keep  a  slight  load  on  the  cable  while 

Содержание EWP2500





















Отзывы: