background image

Miknetum MPR 500

 

 

 

Handling/processing products and materials which are not 
foodstuffs is prohibited! 

 

The lifting aid may be used only for the standard trolleys pro-
vided and must not be overloaded! Lifting of persons is 
strictly prohibited!  

 

Connecting several tablet PCs with a machine is prohibited!  

 
 

2

 

Installation instructions 

Installation and commissioning of the machine may only be carried 
out in the presence of a Rühle service technician or by persons au-
thorised by Rühle. 
Rühle GmbH Lebensmitteltechnik accepts no liability for any damage 
resulting from failure to comply with these operating instructions. 
 

2.1

 

Machine transport and setup 

Please refer to the short instructions supplied with the machine re-
garding transport and setup of the Miknetum. 
 

 

The machine and machine parts must be transported by 2 
persons (1 person to operate the floor truck/1 person to 
supervise transport).  

The power supply line must not be damaged by driving 
over or crushing it! 

The machine must be shut down until a damaged power 
supply line has been repaired! 

 

 

 

 

 
 
 

Ensure that the machine is stable!  

Make sure the machine bases have contact with the 
setup surface and are then tightened!  

Lifting aid, load capacity: Ensure that the max. filling 
quantity of 400 kg per standard trolley is not exceeded! 
 
 

Содержание MPR 500






















Отзывы: