background image

 

Tumbler MPR 300 

 

Temperatures to -10°C may be produced in the drum. 
Wear hand protection!  

 
!!! All life cycles phases 

 

Staying under the lifting aid (standard trolley support) is 
strictly prohibited, and the standard trolleys provided 
must be used! 

 
!!! Maintenance 

 

 

Touching electrical components may cause serious inju-
ries or death.  
Work on electrical equipment of the machine may only be 
carried out by qualified technicians! Always disconnect 
machine from the mains during this process! 

The protective covers may be removed only while per-
forming maintenance (control cabinet, side cover)!  

The start-up alarm (horn) is extremely loud while the side 
cover is off. Wear hearing protection!  

Beware of hot or cold surfaces, e.g. drives, cooling, unit, 
during maintenance work! 

 

 

1.3

 

Intended use  

The Tumbler has been solely designed for mixing, salting/seasoning, 
marinating and tumbling meat products and salads. The room temper-
ature must not exceed 12 °C for reasons of food hygiene!  
 

 

This machine is intended: 

 

for use during work 

 

for use by persons over 18 

 

for use by instructed persons 

 

for a single tablet PC with the RÜHLE application 
software (via Browser, IP address)! 

 

Содержание MPR 300






















Отзывы: