background image

Injector IR 17 

1

 

Safety instructions 

!!! Observe the safety instructions during installation, operation, 
cleaning and maintenance of the Rühle Injector!  

Hazard potentially causing irreversible injuries if 
disregarded.  

Warning potentially causing serious injuries if 
disregarded.  

Note 

Work on electrical equipment of the machine may only 
be carried out by qualified technicians!  
Always disconnect machine from the mains during this 
process! 

Non-ionising radiation is not specifically generated, but 
is only emitted by the electrical equipment (e.g. electric 
motors, power lines or solenoid coils) for technical 
reasons. In addition, the machine has no strong 
permanent magnets. If a safety distance (distance field 
source to implant) of 30 cm is maintained, the influence 
on active implants (e.g. cardiac pacemakers, 
defibrillators) can be excluded with a high degree of 
probability. 

1.1

 

Safety instructions 

!!! A supervisor (responsible person) must be appointed for the 
machine!  
This person must:  

a) Completely read and understand these operating instructions

before transport, commissioning, setup, operation, cleaning,
decommissioning, care/maintenance as well as
dismantling/disposal!

b) Prepare work instructions for intended and safe transport,

commissioning, setup, operation, cleaning, decommissioning,
care/maintenance as well as dismantling/disposal!

Содержание IR 17



















Отзывы: