Ruffneck AH-12A Скачать руководство пользователя страница 16

Страница: 16 / 36

r &

cem

G.2 Heat Exchanger Removal of Single -Motor Unit Heater

Remove unit heater from its mounted location and lower to
a stable working surface.

Remove all louver blades from the front of the cabinet.

Remove the left fan guard and left cabinet side panel
as described below. If the heat exchanger has flanged
connections, also remove the top cabinet panel.

Support the weight of the heat exchanger by the piping
connection while removing the four core bolts that fasten
the heat exchanger to the cabinet. (See Figure 8). Allow
heat exchanger to rest on the bottom of the cabinet.

Remove the two bolts holding the motor mount to the left
side of the cabinet. Support motor mount while removing
these two bolts. Once cabinet side has been removed,
reinsert the bolts in the motor mount. Place a support
under the motor mount to prevent the cabinet from rolling
over during heat exchanger removal (see Figure 11).

With the cabinet side removed and motor mount
supported, slide heat exchanger out of the cabinet. (see
Figure 13). On larger units, assistance may be necessary
due to the weight of the heat exchanger.

To install heat exchanger into cabinet, reverse order of heat
exchanger removal procedure.

G.3 Heat Exchanger Removal of Double-Motor Unit Heater

(Due to the weight of the heat exchanger, an assistant is
recommended to help with the following procedure.)
1.

Remove unit heater from its mounted location and
lower to a stable work surface. To prevent damage to
the bottom piping connection, do not rest heater on
connection while servicing.

Remove all louvers from the front of the cabinet.

Remove the top cabinet panel by removing the four
bolts in the corners of the top panel and the fasteners
along the top of the shrouds (see Figure 13).

Have an assistant support the weight of the heat
exchanger while removing the eight bolts that fasten the
heat exchanger to the cabinet (see Figure 14). Once the
bolts on one side are removed, lower that side of the
heat exchanger to rest on the bottom of the cabinet.
Place a support under the motor mount of the cabinet
to prevent the cabinet from rolling over during heat
exchanger removal (see Figure 13).

Loosen cabinet side panel fasteners but do not remove.
If the heat exchanger has flanged connections also
remove the left side panel.

Lift the heat exchanger up and out through the front of
the cabinet (see Figure 15).

To install heat exchanger procedure, reverse the order
of heat exchanger removal procedure.

Support back

of heater

HEAT EXCHANGER REMOVAL OF

SINGLE- MOTOR UNIT HEATER

1. Remove unit heater from its mounted location and

lower to a stable working surface.

2. Remove all louver blades from the front of

the cabinet.

3. Remove the left fan guard and left cabinet

side panel as described below. If the heat exchanger

has flanged connections, also remove the top

cabinet panel.

4. Support the weight of the heat exchanger by the

piping connection while removing the four core bolts

that fasten the heat exchanger to the cabinet. (See

figure 9). Allow heat exchanger to rest on the bottom

of the cabinet.

5. Remove the two bolts holding the motor mount to

the left side of the cabinet. Support motor mount while

removing these two bolts. Once cabinet side has

been removed, reinsert the bolts in the motor

mount. Place a support under the motor mount to

prevent the cabinet from rolling over during heat

exchanger removal (see Figure 12).

6. With the cabinet side removed and motor mount

supported, slide heat exchanger out of the cabinet.

(see Figure 13). On larger units, assistance may be

necessary due to the weight of the heat exchanger.

7. To install heat exchanger into cabinet, reverse order

of heat exchanger removal procedure.

HEAT EXCHANGER REMOVAL OF

DOUBLE-MOTOR UNIT HEATER

(Due to the weight of the heat exchanger, an assistant is

recommended to help with the following procedure.)

1. Remove unit heater from its mounted location and

lower to a stable work surface. To prevent damage to

the bottom piping connection, do not rest heater on

connection while servicing.

2. Remove all louvers from the front of the cabinet.

3. Remove the top cabinet panel by removing the four

bolts in the corners of the top panel and the fasteners

along the top of the shrouds (see Figure 14).

4. Have an assistant support the weight of the heat

exchanger while removing the eight bolts that fasten

the heat exchanger to the cabinet (see Figure 15).

Once the bolts on one side are removed, lower that

side of the heat exchanger to rest on the bottom of

the cabinet. Place a support under the motor mount

of the cabinet to prevent the cabinet from rolling over

during heat exchanger removal (see Figure 14).

5. Loosen cabinet side panel fasteners but do

not remove. If the heat exchanger has flanged

connections also remove the left side panel.

6. Lift the heat exchanger up and out through the front

of the cabinet (see Figure 16).

7. To install heat exchanger procedure, reverse the

order of heat exchanger removal procedure.

- 9 -

FIGURE 15

FIGURE 14

FIGURE 16

FIGURE 13

Figure 12

Support back

of heater

HEAT EXCHANGER REMOVAL OF

SINGLE- MOTOR UNIT HEATER

1. Remove unit heater from its mounted location and

lower to a stable working surface.

2. Remove all louver blades from the front of

the cabinet.

3. Remove the left fan guard and left cabinet

side panel as described below. If the heat exchanger

has flanged connections, also remove the top

cabinet panel.

4. Support the weight of the heat exchanger by the

piping connection while removing the four core bolts

that fasten the heat exchanger to the cabinet. (See

figure 9). Allow heat exchanger to rest on the bottom

of the cabinet.

5. Remove the two bolts holding the motor mount to

the left side of the cabinet. Support motor mount while

removing these two bolts. Once cabinet side has

been removed, reinsert the bolts in the motor

mount. Place a support under the motor mount to

prevent the cabinet from rolling over during heat

exchanger removal (see Figure 12).

6. With the cabinet side removed and motor mount

supported, slide heat exchanger out of the cabinet.

(see Figure 13). On larger units, assistance may be

necessary due to the weight of the heat exchanger.

7. To install heat exchanger into cabinet, reverse order

of heat exchanger removal procedure.

HEAT EXCHANGER REMOVAL OF

DOUBLE-MOTOR UNIT HEATER

(Due to the weight of the heat exchanger, an assistant is

recommended to help with the following procedure.)

1. Remove unit heater from its mounted location and

lower to a stable work surface. To prevent damage to

the bottom piping connection, do not rest heater on

connection while servicing.

2. Remove all louvers from the front of the cabinet.

3. Remove the top cabinet panel by removing the four

bolts in the corners of the top panel and the fasteners

along the top of the shrouds (see Figure 14).

4. Have an assistant support the weight of the heat

exchanger while removing the eight bolts that fasten

the heat exchanger to the cabinet (see Figure 15).

Once the bolts on one side are removed, lower that

side of the heat exchanger to rest on the bottom of

the cabinet. Place a support under the motor mount

of the cabinet to prevent the cabinet from rolling over

during heat exchanger removal (see Figure 14).

5. Loosen cabinet side panel fasteners but do

not remove. If the heat exchanger has flanged

connections also remove the left side panel.

6. Lift the heat exchanger up and out through the front

of the cabinet (see Figure 16).

7. To install heat exchanger procedure, reverse the

order of heat exchanger removal procedure.

- 9 -

FIGURE 15

FIGURE 14

FIGURE 16

FIGURE 13

Figure 13

Support back

of heater

HEAT EXCHANGER REMOVAL OF

SINGLE- MOTOR UNIT HEATER

1. Remove unit heater from its mounted location and

lower to a stable working surface.

2. Remove all louver blades from the front of

the cabinet.

3. Remove the left fan guard and left cabinet

side panel as described below. If the heat exchanger

has flanged connections, also remove the top

cabinet panel.

4. Support the weight of the heat exchanger by the

piping connection while removing the four core bolts

that fasten the heat exchanger to the cabinet. (See

figure 9). Allow heat exchanger to rest on the bottom

of the cabinet.

5. Remove the two bolts holding the motor mount to

the left side of the cabinet. Support motor mount while

removing these two bolts. Once cabinet side has

been removed, reinsert the bolts in the motor

mount. Place a support under the motor mount to

prevent the cabinet from rolling over during heat

exchanger removal (see Figure 12).

6. With the cabinet side removed and motor mount

supported, slide heat exchanger out of the cabinet.

(see Figure 13). On larger units, assistance may be

necessary due to the weight of the heat exchanger.

7. To install heat exchanger into cabinet, reverse order

of heat exchanger removal procedure.

HEAT EXCHANGER REMOVAL OF

DOUBLE-MOTOR UNIT HEATER

(Due to the weight of the heat exchanger, an assistant is

recommended to help with the following procedure.)

1. Remove unit heater from its mounted location and

lower to a stable work surface. To prevent damage to

the bottom piping connection, do not rest heater on

connection while servicing.

2. Remove all louvers from the front of the cabinet.

3. Remove the top cabinet panel by removing the four

bolts in the corners of the top panel and the fasteners

along the top of the shrouds (see Figure 14).

4. Have an assistant support the weight of the heat

exchanger while removing the eight bolts that fasten

the heat exchanger to the cabinet (see Figure 15).

Once the bolts on one side are removed, lower that

side of the heat exchanger to rest on the bottom of

the cabinet. Place a support under the motor mount

of the cabinet to prevent the cabinet from rolling over

during heat exchanger removal (see Figure 14).

5. Loosen cabinet side panel fasteners but do

not remove. If the heat exchanger has flanged

connections also remove the left side panel.

6. Lift the heat exchanger up and out through the front

of the cabinet (see Figure 16).

7. To install heat exchanger procedure, reverse the

order of heat exchanger removal procedure.

- 9 -

FIGURE 15

FIGURE 14

FIGURE 16

FIGURE 13

Figure 14

Support back

of heater

HEAT EXCHANGER REMOVAL OF

SINGLE- MOTOR UNIT HEATER

1. Remove unit heater from its mounted location and

lower to a stable working surface.

2. Remove all louver blades from the front of

the cabinet.

3. Remove the left fan guard and left cabinet

side panel as described below. If the heat exchanger

has flanged connections, also remove the top

cabinet panel.

4. Support the weight of the heat exchanger by the

piping connection while removing the four core bolts

that fasten the heat exchanger to the cabinet. (See

figure 9). Allow heat exchanger to rest on the bottom

of the cabinet.

5. Remove the two bolts holding the motor mount to

the left side of the cabinet. Support motor mount while

removing these two bolts. Once cabinet side has

been removed, reinsert the bolts in the motor

mount. Place a support under the motor mount to

prevent the cabinet from rolling over during heat

exchanger removal (see Figure 12).

6. With the cabinet side removed and motor mount

supported, slide heat exchanger out of the cabinet.

(see Figure 13). On larger units, assistance may be

necessary due to the weight of the heat exchanger.

7. To install heat exchanger into cabinet, reverse order

of heat exchanger removal procedure.

HEAT EXCHANGER REMOVAL OF

DOUBLE-MOTOR UNIT HEATER

(Due to the weight of the heat exchanger, an assistant is

recommended to help with the following procedure.)

1. Remove unit heater from its mounted location and

lower to a stable work surface. To prevent damage to

the bottom piping connection, do not rest heater on

connection while servicing.

2. Remove all louvers from the front of the cabinet.

3. Remove the top cabinet panel by removing the four

bolts in the corners of the top panel and the fasteners

along the top of the shrouds (see Figure 14).

4. Have an assistant support the weight of the heat

exchanger while removing the eight bolts that fasten

the heat exchanger to the cabinet (see Figure 15).

Once the bolts on one side are removed, lower that

side of the heat exchanger to rest on the bottom of

the cabinet. Place a support under the motor mount

of the cabinet to prevent the cabinet from rolling over

during heat exchanger removal (see Figure 14).

5. Loosen cabinet side panel fasteners but do

not remove. If the heat exchanger has flanged

connections also remove the left side panel.

6. Lift the heat exchanger up and out through the front

of the cabinet (see Figure 16).

7. To install heat exchanger procedure, reverse the

order of heat exchanger removal procedure.

- 9 -

FIGURE 15

FIGURE 14

FIGURE 16

FIGURE 13

Figure 15

Содержание AH-12A





































Результаты поиска

Содержание AH-12A

Отзывы:

Похожие инструкции для AH-12A

Бренды по названию

Популярные бренды

Ruffneck AH-12A, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание AH-12A

Отзывы:

Похожие инструкции для AH-12A

Бренды по названию

Популярные бренды