manualshive.com logo in svg

Ruckus Wireless T811-CM, Руководство по установке

Поделиться
Скачать
Ruckus Wireless T811-CM Скачать руководство пользователя страница 10

T811-CM AP Installation Guide, 800-71436-001 Rev A 

10 

About This Installation Guide 

 

 

 

 

Terms Used in This Guide 

Terms Used in This Guide 

Before continuing, Ruckus Wireless recommends that you become familiar with the following terms: 
•

 

T811-CM: 

T811-CM strand mount AP with integrated CM, which includes the AP and CM and 

the cable  strand interface. 

•

 

AP: 

The Wi-Fi Access Point part of the T811-CM. 

•

 

CM: 

The Cable Modem part of the T811-CM. 

•

 

CMTS: 

Cable modem termination system high speed data services equipment. 

•

 

HFC: 

Hybrid fiber coax broadband network. 

•

 

MSO: 

Multiple system operator. 

 

Related Documentation 

In addition to this guide, each T811-CM documentation set includes the following: 
•

 

User Guide

: Provides detailed information on how to configure the functions of the unit. The User 

Guide is available for download on the Ruckus Wireless Support Web site at 

http://support.ruckuswireless.com/documents

 

•

 

Release Notes

: Provides late-breaking information about the current software release, including 

new features, enhancements, and known issues. If the information in the Release Notes differs 
from the information in this guide, follow the instructions in the Release Notes. 

 

Documentation Feedback 

Ruckus Wireless is interested in improving its documentation and welcomes your comments and 
suggestions. You can email your comments to Ruckus Wireless at 

[email protected]

 

When contacting us, please include the following information: 
•

 

Document title 

•

 

Document part number (on the cover page) 

•

 

Page number (if appropriate) 

For example: 

•

 

T811-CM AP Installation Guide

 

•

 

Part number: 800-71436-001 Rev A 

•

 

Page 

11

 

Содержание T811-CM























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды