RTA 515ENI-N34 Скачать руководство пользователя

Страница: 10 / 48

Real Time Automation, Inc.

1-800-249-1612

Powering the Gateway

The following steps will allow you to properly and safely power the gateway.

Connect a 24VDC power source to the gateway.

The unit draws 125 mA at 24VDC

The gateway has a voltage operating range from 8-28VDC; 24VDC is recommended.

Hazardous Environment Power & Installation Instructions

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, or non-

hazardous locations only.

WARNING

–

EXPLOSION HAZARD -

Do not disconnect equipment unless power has been removed or

the area is known to be non-hazardous.

WARNING

–

EXPLOSION HAZARD -

Substitution of components may impair suitability for Class I,

Division 2.

THIS EQUIPMENT IS AN OPEN-TYPE DEVICE AND IS MEANT TO BE INSTALLED IN AN ENCLOSURE
SUITABLE FOR THE ENVIRONMENT SUCH THAT THE EQUIPMENT IS ONLY ACCESSIBLE WITH THE
USE OF A TOOL.

WARNING

–

POWER JACK (Barrel Connector, J1) IS FOR MAINTENANCE USE ONLY AND MAY ONLY BE

USED WHILE THE AREA IS KNOWN TO BE FREE OF IGNITIBLE CONCENTRATIONS OF FLAMMABLE GASES
OR VAPORS. IT IS NOT TO BE CONNECTED UNDER NORMAL OPERATION.

In a Hazardous Environment, the unit must be powered with between 12-24 VDC; 860 mA (6 W) max.

Supervised. The unit is certified to be operated at -40



C to 50°C.

Warning

improper wiring will cause unit failure

Use the Barrel Connector

the Screw

Terminals power connection,

NOT

both

All manuals and user guides at all-guides.com

Содержание 515ENI-N34

















































Результаты поиска

Содержание 515ENI-N34

Отзывы:

Похожие инструкции для 515ENI-N34

Бренды по названию

Популярные бренды

RTA 515ENI-N34, Руководство пользователя

Результаты поиска

Содержание 515ENI-N34

Отзывы:

Похожие инструкции для 515ENI-N34

Бренды по названию

Популярные бренды